Meetnote
anweat·meetnote·iterations/MeetNote-R0/electronics/MeetNote.kicad_pcb
About the Meetnote PCB
Meetnote is an open source FPGA PCB design by anweat, published on GitHub under the MIT license. It is a 4-layer board measuring 70 × 70 mm, with 31 components from 18 distinct parts.
Its main chip is the ICE40UP5K-SG48ITR, from the FPGA family. By type, the board carries 8 capacitors, 6 resistors, 5 connectors, 4 microphones, 4 switches and 3 diodes.
It belongs with the iot & wireless designs in this gallery.
From the project
MeetNote:可挂佩 AI 会议助手的四轮产品设计与工程研究(R0 概念原型 → R1 设计细化 → R2 金属结构 → R3 Lite)。研究资料,不可投板。
结论:已经建立可编辑产品基线、ECAD/MCAD原型和检查链路;还没有完成可投板的电子工程,更没有实物可用性证明。禁止使用本包制造文件下单。
- Linux SoC:Zero 2 W,512MB RAM、Wi-Fi/BLE、32GB microSD预算。 - 独立FPGA:iCE40UP5K,4×IM69D130同步音频、采样计数、128KiB短缓冲;FPGA收益需和专用音频ADC方案实测比较。 - Camera Module 3自动对焦+1–2×数字裁切,默认只手动拍照,不持续上传视频。 - 推荐尺寸82×118×29mm;78×110×26mm仅为条件化缩小估算,未验证。 - 2500mAh电芯、2.45W输出端平均预算,计老化/损耗/低电量保留后约2.39h;3W则不足2h。 - 35°C环境触温43°C目标尚未证明,散热与RF净空存在2项冲突。 - 自动决定/任务均保持待确认状态,附证据时间戳。
Main components on the Meetnote
Meetnote bill of materials (BOM)
31 components, 18 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ICE40UP5K-SG48ITR | QFN-48-1EP_7x7mm_P0.5mm_EP5.6x5.6mm | U1 |
| 1 | Zero 2 W GPIO via short harness | PinHeader_2x20_P2.54mm_Vertical | J1 |
| 1 | BATTERY 1S | PinHeader_1x02_P2.54mm_Vertical | J2 |
| 1 | REGULATED 5V IN | PinHeader_1x02_P2.54mm_Vertical | J3 |
| 1 | CELL NTC | PinHeader_1x02_P2.54mm_Vertical | J4 |
| 1 | UART 3V3 debug | PinHeader_1x04_P2.54mm_Vertical | J5 |
| 4 | IM69D130 | Infineon_PG-LLGA-5-1 | MK1, MK2, MK3, MK4 |
| 1 | REC_BUTTON | SW_SPST_TL3342 | SW1 |
| 1 | CAM_BUTTON | SW_SPST_TL3342 | SW2 |
| 1 | ZOOM_PLUS | SW_SPST_TL3342 | SW3 |
| 1 | ZOOM_MINUS | SW_SPST_TL3342 | SW4 |
| 1 | RED MIC POWER | LED_0603_1608Metric | D1 |
| 1 | AMBER CAMERA POWER | LED_0603_1608Metric | D2 |
| 1 | BLUE UPLOAD | LED_0603_1608Metric | D3 |
| 8 | 100nF 10V | C_0603_1608Metric | C1, C2, C3, C4, C5, C6, C7, C8 |
| 1 | 100R PLL filter provisional | R_0603_1608Metric | R1 |
| 2 | 10K 10k | R_0603_1608Metric | R2, R3 |
| 3 | 1k provisional | R_0603_1608Metric | R4, R5, R6 |
Meetnote design files
The KiCad project lives in the anweat/meetnote repository on GitHub; these links point at the commit this page was built from.
Meetnote: common questions
What microcontroller does the Meetnote use?
The Meetnote is built around the ICE40UP5K-SG48ITR, from the FPGA family.
How big is the Meetnote PCB?
The Meetnote measures 70 × 70 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Meetnote?
31 components, from 18 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Meetnote design files?
From the anweat/meetnote repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Meetnote design in my own project?
Yes, under the terms of its MIT license, which anweat chose for the repository.
Can I test firmware for the Meetnote without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug FPGA firmware against it before you order a PCB.
Similar boards
FPGA
Base board
GlasgowEmbedded
80 × 49 mm222 parts4L0BSD2.2kFPGA
Thunderscope Rev5.3
EEVengers
122.5 × 103.5 mm817 parts6LMIT1.3kFPGA
Usb sniffer
ataradov
58.2 × 38.1 mm86 parts2LBSD-3-Clause1.3kFPGA
Tomu, I'm
theacodes
13 × 9.4 mm40 parts4LMIT1.1kFPGA
Icepi zero
cheyao
65 × 30 mm143 parts4LSHL-2.1865FPGA
Gcvideo
ikorb
49 × 30 mm44 parts4LNo license765