Attendance device
Aryalleh·Attendance-device·hardware/rfid-door-controller.kicad_pcb
About the Attendance device PCB
Attendance device is an open source ESP8266 PCB design by Aryalleh, published on GitHub. It is a 2-layer board measuring 85 × 40 mm, with 14 components from 13 distinct parts.
Its main chip is the WeMos D1 mini, from the ESP8266 family. By type, the board carries 4 resistors, 2 transistors, 2 connectors, 2 diodes, 2 capacitors and 1 module.
From the project
A 2-layer, 85 × 40 mm, all through-hole carrier for the RFID attendance device: the Wemos D1 mini plugs into two 1×8 female headers, the RC522 into a 1×8 socket on the left edge, and the board adds the two status LEDs, the buzzer driver and a header for an optional relay module.
A 2-layer, 85 × 40 mm, all through-hole carrier for the RFID attendance device: the Wemos D1 mini plugs into two 1×8 female headers, the RC522 into a 1×8 socket on the left edge, and the board adds the two status LEDs, the buzzer driver and a header for an optional relay module.
Power comes only from the D1 mini's micro-USB socket (5 V, ≥ 500 mA). The D1 mini's own regulator feeds the RC522 with 3.3 V. Give a door lock its own supply; never run it from the USB 5 V.

Main components on the Attendance device
Attendance device bill of materials (BOM)
14 components, 13 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | WeMos D1 mini | WEMOS_D1_mini_light | A1 |
| 1 | BC547 | TO-92_Inline | Q1 |
| 1 | BC337 | TO-92_Inline | Q2 |
| 1 | RC522 | PinSocket_1x08_P2.54mm_Vertical | J1 |
| 1 | RELAY (opt.) | PinHeader_1x03_P2.54mm_Vertical | J2 |
| 1 | 5V active | Buzzer_12x9.5RM7.6 | BZ1 |
| 1 | GREEN | LED_D5.0mm | D1 |
| 1 | RED | LED_D5.0mm | D2 |
| 1 | 100nF | C_Disc_D5.0mm_W2.5mm_P5.00mm | C1 |
| 1 | 47uF 10V | CP_Radial_D5.0mm_P2.00mm | C2 |
| 2 | 220 | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R2 |
| 1 | 47k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R3 |
| 1 | 10k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R4 |
Attendance device design files
The KiCad project lives in the Aryalleh/Attendance-device repository on GitHub; these links point at the commit this page was built from.
Attendance device: common questions
What microcontroller does the Attendance device use?
The Attendance device is built around the WeMos D1 mini, from the ESP8266 family.
How big is the Attendance device PCB?
The Attendance device measures 85 × 40 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Attendance device?
14 components, from 13 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Attendance device design files?
From the Aryalleh/Attendance-device repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Attendance device design in my own project?
The repository has no license, so all rights stay with Aryalleh. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Attendance device without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP8266 firmware against it before you order a PCB.
Similar boards
ESP8266
ESP8266ControllerCircuit
stuartpittaway
75 × 30 mm20 parts2LCC-BY-NC-4.01.1kESP8266
HASwitchPlate
aderusha
60 × 40 mm8 parts2LMIT738ESP8266
RatGDO-OpenSource-Bare-ESP8266
Kaldek
55 × 82.7 mm20 parts2LMIT506ESP8266
RatGDO-OpenSource-D1Mini-ESP8266
Kaldek
47.8 × 63.3 mm12 parts2LMIT506ESP8266
Goatgdo
Kaldek
32.9 × 53.3 mm23 parts2LMIT506ESP8266
Iaq board
nkitanov
70.1 × 43.2 mm17 parts2LNo license398