Stylus synth

atomicra1n·stylus-synth·pcb/stylus-synth.kicad_pcb

Stylus synth PCB layout, top view — open source RP2040/RP2350 board by atomicra1n

About the Stylus synth PCB

Stylus synth is an open source RP2040/RP2350 PCB design by atomicra1n, published on GitHub. It is a 2-layer board measuring 100 × 100 mm, with 50 components from 21 distinct parts.

Its main chip is the RP2040-Zero, from the RP2040/RP2350 family. Other key parts include the LM386. By type, the board carries 29 resistors, 10 capacitors, 4 connectors, 2 ICs, 2 switches and 1 diode.

It belongs with the audio and test & measurement designs in this gallery.

From the project

A small synthesizer played with a stylus or a probe (such as a multimeter one). It has 20 copper pads on the PCB acting as a keyboard, a speaker and a headphone jack. Controlled by an RP2040-Zero featuring an analog vactrol circuit.

A small synthesizer played with a stylus or a probe (such as a multimeter one). It has 20 copper pads on the PCB acting as a keyboard, a speaker and a headphone jack. Controlled by an RP2040-Zero featuring an analog vactrol circuit.

- 20 note keyboard (note C to G) from exposed copper pads, playable with a conductive stylus - Notes fade out naturally when the stylus is lifted (thanks to the Vactrol circuit, LED + photoresistor) - Volume and decay knobs - Octave button and waveform button (supports square wave, saw wave and triangle wave) - Speaker and a headphone jack that automatically…

Stylus synth, from the project README
From the project README

Main components on the Stylus synth

Stylus synth bill of materials (BOM)

50 components, 21 distinct parts.

QtyPartRefs
1
~
U1
1
LM386
U2
1
STYLUS
J1
1
STYLUS_PADS
J2
1
ST-214C
J3
1
SPEAKER
J4
2
10k
RV1, RV2
1
OCTAVE
SW1
1
WAVE
SW2
1
Green 5mm
D1
2
100nF
C1, C6
3
10nF
C2, C3, C4
2
10uF
C5, C8
2
220uF
C7, C9
1
47nF
C10
23
1k
R1, R2, R3, R4, R5, R6, R7, R8 +15
1
1M
R22
1
330
R25
1
LDR5516
R26
2
100k
R27, R28
Show 1 more
QtyPartRefs
1
10
R29

Stylus synth design files

The KiCad project lives in the atomicra1n/stylus-synth repository on GitHub; these links point at the commit this page was built from.

Stylus synth: common questions

What microcontroller does the Stylus synth use?

The Stylus synth is built around the RP2040-Zero, from the RP2040/RP2350 family.

How big is the Stylus synth PCB?

The Stylus synth measures 100 × 100 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Stylus synth?

50 components, from 21 distinct parts. The full bill of materials is listed on this page.

Where can I download the Stylus synth design files?

From the atomicra1n/stylus-synth repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Stylus synth design in my own project?

The repository has no license, so all rights stay with atomicra1n. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Stylus synth without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.

Similar boards