IotBoard
AVSRAVITEJA·iotBoard
About the IotBoard PCB
IotBoard is an open source ESP32 PCB design by AVSRAVITEJA, published on GitHub. It is a 2-layer board measuring 152 × 120.6 mm, with 23 components from 17 distinct parts.
Its main chip is the MODULE_113991054, from the ESP32 family. Other key parts include the SEN-13879 and ARDUINO_MEGA_2560_REV3_A000067. By type, the board carries 10 connectors, 7 ICs, 5 resistors and 1 module.
It belongs with the iot & wireless, robotics & motion and sensors designs in this gallery.
From the project
The sensor board includes a current sensing circuit to monitor power consumption, a voltage sensing module for battery and power system tracking, a temperature sensor to detect overheating or monitor environmental conditions, and an interface for load cells to measure payload wei
The sensor board includes a current sensing circuit to monitor power consumption, a voltage sensing module for battery and power system tracking, a temperature sensor to detect overheating or monitor environmental conditions, and an interface for load cells to measure payload weight or dynamic load changes during flight. These sensors provide real-time insights into the UAV's operational status, making it easier to detect anomalies, prevent system failures, and manage power resources efficiently.
Main components on the IotBoard
IotBoard bill of materials (BOM)
23 components, 17 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 3 | SEN-13879 | SPARKFUN_SEN-13879 | U1, U2, U3 |
| 1 | ~ | Untitled | U4 |
| 1 | ~ | MODULE_113991054 | U5 |
| 1 | ~ | rtcModule | U6 |
| 1 | ~ | AMASS_XT60PW-M_1x02_P7.20mm_Horizontal | U8 |
| 1 | ARDUINO_MEGA_2560_REV3_A000067 | ARDUINO_ARDUINO_MEGA_2560_REV3_A000067 | A1 |
| 1 | LOADCELL SECTION | RJ45_Amphenol_54602-x08_Horizontal | J2 |
| 1 | WING TILT | RJ45_Amphenol_54602-x08_Horizontal | J3 |
| 1 | MOTOR currents | RJ45_Amphenol_54602-x08_Horizontal | J4 |
| 1 | UART | PinSocket_2x02_P2.54mm_Vertical | J5 |
| 1 | MOTOR RPM | RJ45_Amphenol_54602-x08_Horizontal | J6 |
| 1 | MOTOR TEMP | RJ45_Amphenol_54602-x08_Horizontal | J7 |
| 1 | MOT_C_SIG | PinHeader_1x04_P2.54mm_Vertical | J8 |
| 1 | MOT_C_VCC | PinHeader_1x04_P2.54mm_Vertical | J9 |
| 1 | MOT_C_GND | PinHeader_1x04_P2.54mm_Vertical | J10 |
| 1 | ECU | RJ45_Amphenol_54602-x08_Horizontal | J11 |
| 5 | R | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R2, R3, R4, R5 |
IotBoard design files
The KiCad project lives in the AVSRAVITEJA/iotBoard repository on GitHub; these links point at the commit this page was built from.
- LayoutiotBoardWingHead.kicad_pcb
- SchematiciotBoardWingHead.kicad_sch
IotBoard: common questions
What microcontroller does the IotBoard use?
The IotBoard is built around the MODULE_113991054, from the ESP32 family.
How big is the IotBoard PCB?
The IotBoard measures 152 × 120.6 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the IotBoard?
23 components, from 17 distinct parts. The full bill of materials is listed on this page.
Where can I download the IotBoard design files?
From the AVSRAVITEJA/iotBoard repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the IotBoard design in my own project?
The repository has no license, so all rights stay with AVSRAVITEJA. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the IotBoard without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k