Buildbutton
ayoy·kicad-projects·buildbutton/v4/buildbutton.kicad_pcb
About the Buildbutton PCB
Buildbutton is an open source ESP32 PCB design by ayoy, published on GitHub. It is a 2-layer board measuring 34 × 33 mm, with 18 components from 15 distinct parts.
Its main chip is the ESP32_DATA, from the ESP32 family. Other key parts include the LM1117-3.3 and ESP_UART. By type, the board carries 5 connectors, 3 ICs and 1 transistor.
Main components on the Buildbutton
Buildbutton bill of materials (BOM)
18 components, 15 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LM1117-3.3 | SOT-223 | U1 |
| 1 | ESP32_DATA | Socket_Strip_Straight_2x01_Pitch2.54mm | U3 |
| 1 | ESP_UART | ESP_UART_Socket_Strip | U4 |
| 1 | IRLL014N | SOT-223 | Q1 |
| 1 | BATTERY | Socket_Strip_Angled_1x02_Pitch2.54mm | J1 |
| 1 | IO0 | Socket_Strip_Straight_2x01_Pitch2.54mm | J2 |
| 1 | BUTTON | Socket_Strip_Angled_1x02_Pitch2.54mm | J3 |
| 1 | LED | Socket_Strip_Angled_1x02_Pitch2.54mm | J4 |
| 1 | PROG | Socket_Strip_Angled_1x06_Pitch2.54mm | J5 |
| 1 | 100uF | CP_Elec_6.3x7.7 | C_BLK1 |
| 2 | 2.2nF | C_1206 | C_EN1, C_IO0 |
| 2 | 10uF | CP_Tantalum_Case-A_EIA-3216-18_Reflow | C_IN1, C_OUT1 |
| 1 | 100nF | CP_Tantalum_Case-A_EIA-3216-18_Reflow | C_PWR1 |
| 2 | 10k | R_1206_HandSoldering | R_BTN1, R_EN1 |
| 1 | 4.7k | R_1206_HandSoldering | R_IO0 |
Buildbutton design files
The KiCad project lives in the ayoy/kicad-projects repository on GitHub; these links point at the commit this page was built from.
Buildbutton: common questions
What microcontroller does the Buildbutton use?
The Buildbutton is built around the ESP32_DATA, from the ESP32 family.
How big is the Buildbutton PCB?
The Buildbutton measures 34 × 33 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Buildbutton?
18 components, from 15 distinct parts. The full bill of materials is listed on this page.
Where can I download the Buildbutton design files?
From the ayoy/kicad-projects repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Buildbutton design in my own project?
The repository has no license, so all rights stay with ayoy. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Buildbutton without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in kicad-projects
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k