Embroidery nfc
borisnimcevic·embroidery-nfc·hardware/embroidery-nfc.kicad_pcb
About the Embroidery nfc PCB
Embroidery nfc is an open source PCB design by borisnimcevic, published on GitHub under the CERN-OHL-S-2.0 license. It is a 2-layer board measuring 85 × 54 mm, with 9 components from 5 distinct parts.
Other key parts include the NT3H2111W0FT1X. By type, the board carries 3 diodes, 3 resistors, 2 capacitors and 1 IC.
It belongs with the rf & radio and power & battery designs in this gallery.
From the project
Batteryless NFC business card: NTAG I2C plus, PCB loop antenna and LEDs powered by NFC energy harvesting (KiCad)
A batteryless NFC business card. Tap it with a phone and it opens a URL, while three LEDs light up from energy harvested out of the phone's NFC field.
- NXP NT3H2111 (NTAG I2C plus) stores the URL as an NDEF record. The phone powers it through the antenna, so no battery is needed. - PCB loop antenna: a 4-turn, 70 x 46 mm coil around the edge of the card, about 2.66 uH (ST eDesignSuite). It resonates with the chip's 50 pF input capacitance at about 13.8 MHz, slightly above 13.56 MHz, which is where an NFC tag should sit. - Energy harvesting: the chip's VOUT pin delivers about 2 V / up to ~5…

Main components on the Embroidery nfc
Embroidery nfc bill of materials (BOM)
9 components, 5 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | NT3H2111W0FT1X | SOIC-8_3.9x4.9mm_P1.27mm | U1 |
| 3 | Red | LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1, D2, D3 |
| 1 | 2-10pF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1 |
| 1 | 150nF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2 |
| 3 | 220 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2, R3 |
Embroidery nfc design files
The KiCad project lives in the borisnimcevic/embroidery-nfc repository on GitHub; these links point at the commit this page was built from.
Embroidery nfc: common questions
How big is the Embroidery nfc PCB?
The Embroidery nfc measures 85 × 54 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Embroidery nfc?
9 components, from 5 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Embroidery nfc design files?
From the borisnimcevic/embroidery-nfc repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Embroidery nfc design in my own project?
Yes, under the terms of its CERN-OHL-S-2.0 license, which borisnimcevic chose for the repository.
Similar boards
EinkPDA screen
TalismanDesign
95 × 54 mm27 parts2LApache-2.02.0kStack chan
stack-chan
50 × 50 mm33 parts2LApache-2.01.7kDisplay Carrier
AxxAxx
35.6 × 58.2 mm5 parts2LGPL-3.01.7kProgrammingAdapter
stuartpittaway
10.5 × 83 mm3 parts2LCC-BY-NC-4.01.1kTemperaturePCB PANEL
stuartpittaway
116 × 75.5 mm178 parts2LCC-BY-NC-4.01.1kModule 16S PassiveBalanceAddOn
stuartpittaway
61 × 74 mm86 parts2LCC-BY-NC-4.01.1k