DIY-E22-LoRa-Radio
BrokenCircuitRanch·DIY-E22-LoRa-Radio·kicad/S3DIY.kicad_sch
About the DIY-E22-LoRa-Radio PCB
DIY-E22-LoRa-Radio is an open source ESP32 PCB design by BrokenCircuitRanch, published on GitHub under the CC-BY-NC-4.0 license. It is a board, with 14 components from 9 distinct parts.
Its main chip is the ESP32-S3-DEVKITC-1U-N8R8, from the ESP32 family. By type, the board carries 4 resistors, 2 jumpers, 2 capacitors, 1 IC and 1 connector.
It belongs with the rf & radio and iot & wireless designs in this gallery.
From the project
DIY ESP32-S3 + Ebyte E22 900 MHz LoRa radio, Anvil Link compatible: schematic, KiCad source, BOM, build notes
A build-it-yourself 900 MHz LoRa radio from off-the-shelf modules: an ESP32-S3 DevKitC, an Ebyte E22 radio card, and optional Ethernet, GPS and OLED. Hand-wire it point to point or lay out a PCB from the KiCad schematic.
It uses the same pin map as the BCR Hammer V3, so it runs the Anvil Link firmware built for that board.
Recommended additions: a 100 nF capacitor right at the radio's VCC pin and another at the W5500's 3V3 pin, and 100-220 µF bulk on 5 V near the radio. The 30/33 dBm cards pull well over half an amp while transmitting (the 33 dBm card over 1 A). Power the board from a 5 V…
Main components on the DIY-E22-LoRa-Radio
DIY-E22-LoRa-Radio bill of materials (BOM)
14 components, 9 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-DEVKITC-1U-N8R8 | MODULE_ESP32-S3-DEVKITC-1U-N8R8 | U5 |
| 1 | SMA | SMA_Wurth_60312002114503_Vertical | J3 |
| 2 | Jumper_2_Open | PinHeader_1x02_P2.54mm_Vertical | JP1, JP2 |
| 1 | E22x Type Radio | XCVR_E22-900M30S | MODULE0 |
| 1 | WIZ820IO | MODULE_WIZ820IO | MODULE1 |
| 1 | GPS | SAMTEC_MTSW-105-07-T-S-140 | Module2 |
| 1 | OLED | SAMTEC_MTLW-104-X-X-S-X | Module3 |
| 2 | 10UF 10uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2, C3 |
| 4 | 10K | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2, R3, R4 |
DIY-E22-LoRa-Radio design files
The KiCad project lives in the BrokenCircuitRanch/DIY-E22-LoRa-Radio repository on GitHub; these links point at the commit this page was built from.
- Schematickicad/S3DIY.kicad_sch
- BOMBOM.csv
DIY-E22-LoRa-Radio: common questions
What microcontroller does the DIY-E22-LoRa-Radio use?
The DIY-E22-LoRa-Radio is built around the ESP32-S3-DEVKITC-1U-N8R8, from the ESP32 family.
How many components are on the DIY-E22-LoRa-Radio?
14 components, from 9 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the DIY-E22-LoRa-Radio design files?
From the BrokenCircuitRanch/DIY-E22-LoRa-Radio repository on GitHub, which has the schematic and the BOM; the links under Design files point to each one.
Can I use the DIY-E22-LoRa-Radio design in my own project?
It is published under CC-BY-NC-4.0, which limits how it may be reused; read the license before building on it.
Can I test firmware for the DIY-E22-LoRa-Radio without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k