Stm32-mini
cheyao·Stm32-mini·hardware/stm32-ulp.kicad_pcb
About the Stm32-mini PCB
Stm32-mini is an open source STM32 PCB design by cheyao, published on GitHub under the SHL-2.1 license. It is a 2-layer board measuring 18.5 × 50.3 mm, with 31 components from 21 distinct parts.
Its main chip is the STM32U073K8Ux, from the STM32 family. Other key parts include the SRV05-4, MCP73832-2-OT and TPS7A0233DBV. By type, the board carries 11 capacitors, 6 resistors, 5 connectors, 4 ICs, 2 diodes and 1 transistor.
It belongs with the displays & leds designs in this gallery.
From the project
A small STM32U073 devboard made for low power stuff. It runs off USB-C or a LiPo, and has a LiPo charging circuit. The whole power chain is picked so the board idles at basically nothing when the MCU is asleep.
A small STM32U073 devboard made for low power stuff. It runs off USB-C or a LiPo, and has a LiPo charging circuit. The whole power chain is picked so the board idles at basically nothing when the MCU is asleep.
The STM32U0 is stm's ulp stm32. With a 56MHz Cortex-M0+, 64KB flash, and 40KB SRAM, crystal-less USB, and ~100nA sleep. The board uses a STM32U073K8Ux chip, with 3.3V from a ldo with 25nA Iq.

Main components on the Stm32-mini
Stm32-mini bill of materials (BOM)
31 components, 21 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | SRV05-4 | SOT-23-6 | U2 |
| 1 | STM32U073K8Ux | QFN-32-1EP_5x5mm_P0.5mm_EP3.45x3.45mm_ThermalVias | U3 |
| 1 | MCP73832-2-OT | SOT-23-5 | U4 |
| 1 | TPS7A0233DBV | SOT-23-5 | U5 |
| 1 | AO3401A | SOT-23 | Q6 |
| 1 | 32.768kHz | Crystal_SMD_3215-2Pin_3.2x1.5mm | Y1 |
| 1 | USB_C_Receptacle_USB2.0_14P | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | LiPo | HCTL_JST_PH_HC-PH-2AWT-B_2P | J2 |
| 1 | SWD | PinHeader_1x03_P2.54mm_Vertical | J3 |
| 2 | Conn_01x15 | PinHeader_1x15_P2.54mm_Vertical | J4, J5 |
| 1 | SW_Push | SW_Push_SPST_TSA016 | SW2 |
| 1 | LED | LED_0402_1005Metric | D8 |
| 1 | BAT54 | D_SOD-523 | D9 |
| 2 | 7pF | C_0402_1005Metric | C13, C14 |
| 3 | 4.7uF | C_0402_1005Metric | C15, C16, C19 |
| 3 | 1uF | C_0402_1005Metric | C17, C18, C20 |
| 3 | 100nF | C_0402_1005Metric | C21, C22, C23 |
| 2 | 5.1k | R_0402_1005Metric | R1, R2 |
| 2 | 10k | R_0402_1005Metric | R13, R16 |
| 1 | 3.3k | R_0402_1005Metric | R14 |
Show 1 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 1.5k | R_0402_1005Metric | R15 |
Stm32-mini design files
The KiCad project lives in the cheyao/Stm32-mini repository on GitHub; these links point at the commit this page was built from.
- Layouthardware/stm32-ulp.kicad_pcb
- Schematichardware/stm32-ulp.kicad_sch
Stm32-mini: common questions
What microcontroller does the Stm32-mini use?
The Stm32-mini is built around the STM32U073K8Ux, from the STM32 family.
How big is the Stm32-mini PCB?
The Stm32-mini measures 18.5 × 50.3 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Stm32-mini?
31 components, from 21 distinct parts. The full bill of materials is listed on this page.
Where can I download the Stm32-mini design files?
From the cheyao/Stm32-mini repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Stm32-mini design in my own project?
It is published under SHL-2.1, which limits how it may be reused; read the license before building on it.
Can I test firmware for the Stm32-mini without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k