20 open source boards using the MCP73832-2-OT

Real designs built with the MCP73832-2-OT, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

20 boardsClear filters|Most starred

How designs wire the MCP73832-2-OT

Read from the KiCad layouts of 18 open source designs, one per repository: what each pin of the MCP73832-2-OT connects to, and the resistors, capacitors and other passives placed on it.

  • The PROG pin has a resistor to GND on 17 of 18 designs, most often 10 kΩ (then 2 kΩ).
  • The VBAT pin has a decoupling capacitor on 16 of 18 designs, most often 4.7 µF (then 1 µF).
  • The VDD pin has a decoupling capacitor on 13 of 18 designs, most often 4.7 µF (then 10 µF).
  • The STAT pin has a series resistor on 10 of 18 designs, most often 1 kΩ (then 470 Ω).
STATpin 1Connected to: Signal 100%
  • Series resistor on 56% · 1 kΩ (4), 470 Ω (3), 4.7 kΩ (2)
VSSpin 2Connected to: GND 94%
VBATpin 3Connected to: BATT 61% · a signal 39%
  • Decoupling capacitor on 89% · 4.7 µF (14), 1 µF (3), 10 µF (2)
VDDpin 4Connected to: VBUS 61% · a signal 39%
  • Decoupling capacitor on 72% · 4.7 µF (12), 10 µF (4)
PROGpin 5Connected to: Signal 94%
  • Resistor to GND on 94% · 10 kΩ (6), 2 kΩ (5), 2.5 kΩ (2)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include MiniBot by DDeGonge, Feuchtraumabzweigdose by transportkollektiv, Avr transistor tester by vitaliy-bobrov and PlayaNavigator by zshivers.

The MCP73832-2-OT in open source designs

The gallery holds 20 open source boards using the MCP73832-2-OT from 19 GitHub repositories; a typical one measures about 50.5 × 51.4 mm and carries around 65 components.

79% are two-layer designs, the rest use four layers or more, and 65% carry an open source license.

The most starred is MiniBot by DDeGonge.

Microcontrollers on boards using the MCP73832-2-OT

MCP73832-2-OT: common questions

Where can I find a MCP73832-2-OT reference design?

Each of the 20 boards on this page is a real design using the MCP73832-2-OT. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the MCP73832-2-OT PROG pin?

The PROG pin has a resistor to GND on 17 of 18 designs, most often 10 kΩ (then 2 kΩ). Counted from the KiCad layouts of 18 open source designs using the MCP73832-2-OT.

What decoupling capacitors do designs use on the MCP73832-2-OT VBAT pin?

The VBAT pin has a decoupling capacitor on 16 of 18 designs, most often 4.7 µF (then 1 µF). Counted from the KiCad layouts of 18 open source designs using the MCP73832-2-OT.

What decoupling capacitors do designs use on the MCP73832-2-OT VDD pin?

The VDD pin has a decoupling capacitor on 13 of 18 designs, most often 4.7 µF (then 10 µF). Counted from the KiCad layouts of 18 open source designs using the MCP73832-2-OT.

What parts are used alongside the MCP73832-2-OT?

The AP2112K-3.3, ESP32-S3-WROOM-1, ESP32-WROOM-32E_(16MB), TCA9534 and USBLC6-2SC6 appear in the most repositories here.

Which microcontrollers do boards using the MCP73832-2-OT use?

Most are built on ESP32 (8), AVR/Arduino (2), Nordic nRF (2) and Raspberry Pi (2).

How big is a typical board using the MCP73832-2-OT?

The median is 50.5 × 51.4 mm, and 79% are two-layer designs.

What is the most popular open source board using the MCP73832-2-OT?

By GitHub stars, MiniBot by DDeGonge, with 40 stars.

Can I simulate one of these boards using the MCP73832-2-OT before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part