Esp32-homespan garagedoor opener
chrisdaun·esp32-homespan-garagedoor-opener·KiCAD/Garage Door Opener/Garage Door Opener.kicad_pcb
About the Esp32-homespan garagedoor opener PCB
Esp32-homespan garagedoor opener is an open source ESP32 PCB design by chrisdaun, published on GitHub. It is a 2-layer board measuring 57 × 57 mm, with 8 components from 8 distinct parts.
Its main chip is the YD-ESP32-S3, from the ESP32 family. By type, the board carries 2 connectors, 1 IC, 1 transistor, 1 relay, 1 switch and 1 diode.

Main components on the Esp32-homespan garagedoor opener
Esp32-homespan garagedoor opener bill of materials (BOM)
8 components, 8 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | YD-ESP32-S3 | YD-ESP32-S3 | U1 |
| 1 | PN2222A | TO-92_Inline | Q1 |
| 1 | Screw_Terminal_01x03 | TerminalBlock_Phoenix_MKDS-1,5-3_1x03_P5.00mm_Horizontal | J1 |
| 1 | Conn_01x02_Pin | PinHeader_1x02_P2.54mm_Vertical | J3 |
| 1 | JQC-3FF-S-Z | JQC-3FF-S-Z | K1 |
| 1 | SW_Push | SW_SPST_SKQG_WithStem | SW1 |
| 1 | D | D_MiniMELF | D1 |
| 1 | 1kOhm | R_0805_2012Metric | R1 |
Esp32-homespan garagedoor opener design files
The KiCad project lives in the chrisdaun/esp32-homespan-garagedoor-opener repository on GitHub; these links point at the commit this page was built from.
Esp32-homespan garagedoor opener: common questions
What microcontroller does the Esp32-homespan garagedoor opener use?
The Esp32-homespan garagedoor opener is built around the YD-ESP32-S3, from the ESP32 family.
How big is the Esp32-homespan garagedoor opener PCB?
The Esp32-homespan garagedoor opener measures 57 × 57 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Esp32-homespan garagedoor opener?
8 components, from 8 distinct parts. The full bill of materials is listed on this page.
Where can I download the Esp32-homespan garagedoor opener design files?
From the chrisdaun/esp32-homespan-garagedoor-opener repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Esp32-homespan garagedoor opener design in my own project?
The repository has no license, so all rights stay with chrisdaun. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Esp32-homespan garagedoor opener without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k