Acelerografo
About the Acelerografo PCB
Acelerografo is an open source PIC PCB design by Daniele21211, published on GitHub. It is a 4-layer board measuring 89.5 × 88.5 mm, with 56 components from 30 distinct parts.
Its main chip is the DSPIC33EP256MC202-I/SO, from the PIC family. Other key parts include the MP2303ADN-LF-Z, EVAL-ADXL355Z and AMS1117-3.3. By type, the board carries 20 capacitors, 10 diodes, 10 resistors, 5 ICs, 5 connectors and 1 battery holder.
Main components on the Acelerografo
Acelerografo bill of materials (BOM)
56 components, 30 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ~ | SOIC-20W_7.5x12.8mm_P1.27mm | IC1 |
| 1 | DSPIC33EP256MC202-I/SO dsPIC33EP256MC202-I/SO | SOIC-28W_7.5x17.9mm_P1.27mm | U1 |
| 1 | MP2303ADN-LF-Z MP2303ADN | SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.62x3.51mm | U2 |
| 1 | EVAL-ADXL355Z ~ | ADXL355Z | U3 |
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U4 |
| 2 | 1725656 Conn_01x02_Pin | TerminalBlock_Phoenix_MPT-0,5-2-2.54_1x02_P2.54mm_Horizontal | J1, J2 |
| 1 | PZ254V-11-06P Conn_PIC_ICSP_ICD | PinHeader_1x06_P2.54mm_Vertical | J3 |
| 1 | Conn_01x09_Pin | PinHeader_1x09_P2.54mm_Vertical | J5 |
| 1 | ZX-PM2.54-2-20PY Raspberry_Pi_3B+ | PinSocket_2x20_P2.54mm_Vertical | J6 |
| 1 | KH-CR2032-2-1 Battery_Cell | Battery_Panasonic_CR2032-HFN_Horizontal_CircularHoles | BT1 |
| 1 | 5GSH935 SW_MEC_5E | SW_MEC_5GSH9 | SW1 |
| 3 | PZ254V-11-02P JUWPER 2*1 | TestPoint_2Pads_Pitch2.54mm_Drill0.8mm | W1, W2, W3 |
| 1 | 1N4148WS | D_SOD-323 | D1 |
| 2 | PTVS12VS1UTR.115 | Nexperia_CFP3_SOD-123W | D2, D4 |
| 3 | SS34 | D_SMA | D3, D5, D10 |
| 1 | B5819WSL-TP B5819W_SL | D_SOD-323F | D6 |
| 1 | 1N4148WS | D_SOD-323F | D7 |
| 2 | NCD0805R1 Red | LED_0805_2012Metric | D8, D9 |
| 1 | 22UH 22uH | L_APV_APH0650 | L1 |
| 1 | 1UF 1uF | C_0603_1608Metric | C1 |
Show 10 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 4 | 22UF 22uF | C_1206_3216Metric | C2, C3, C9, C11 |
| 9 | 100NF 100nF | C_0603_1608Metric | C4, C5, C6, C7, C8, C12, C14, C17 +1 |
| 1 | 3.3NF 3.3nF | C_0603_1608Metric | C10 |
| 3 | 220UF 220uF | CP_Elec_6.3x9.9 | C13, C15, C19 |
| 2 | 10NF 10nF | C_0603_1608Metric | C16, C18 |
| 6 | 4K7 4k7 | R_0603_1608Metric | R1, R4, R5, R6, R9, R10 |
| 1 | 47K | R_0402_1005Metric | R2 |
| 1 | 220K | R_0402_1005Metric | R3 |
| 1 | 5K6 | R_0402_1005Metric | R7 |
| 1 | 100K | R_0402_1005Metric | R8 |
Acelerografo design files
The KiCad project lives in the Daniele21211/RedSismicaDelAustro repository on GitHub; these links point at the commit this page was built from.
Acelerografo: common questions
What microcontroller does the Acelerografo use?
The Acelerografo is built around the DSPIC33EP256MC202-I/SO, from the PIC family.
How big is the Acelerografo PCB?
The Acelerografo measures 89.5 × 88.5 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Acelerografo?
56 components, from 30 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Acelerografo design files?
From the Daniele21211/RedSismicaDelAustro repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Acelerografo design in my own project?
The repository has no license, so all rights stay with Daniele21211. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Acelerografo without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug PIC firmware against it before you order a PCB.
More boards in RedSismicaDelAustro
Similar boards
PICPslab hardware
fossasia
99 × 53.3 mm187 parts4LApache-2.01.7k
PICMicro 8088
skiselev
152.4 × 101.6 mm71 partsGPL-3.0414
PICGB-CARTPP-DIY
Gekkio
100 × 100 mm22 parts2LCC-BY-4.0376
PICGB-MBCTEST
51.4 × 61 mm32 parts2LCC-BY-4.0376
PICGB-BENCH-G1
100 × 100 mm98 parts4LCC-BY-4.0376
PICGB-LIVE32
51.4 × 61 mm46 parts4LCC-BY-4.0376