Maze bot
danielljeon·maze_bot_pcb
About the Maze bot PCB
Maze bot is an open source STM32 PCB design by danielljeon, published on GitHub. It is a 4-layer board, with 22 components from 15 distinct parts.
Its main chip is the STM32L432KCU6, from the STM32 family. Other key parts include the LD1117S33CTR, 4754, TB6612FNG and SN74LVC1G04DCK. By type, the board carries 9 capacitors, 6 ICs, 6 connectors and 1 switch.
Main components on the Maze bot
Maze bot bill of materials (BOM)
22 components, 15 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LD1117S33CTR | SOT-223-3_TabPin2 | U1 |
| 1 | 4754 Adafruit | adafruit_4754_bno085 | U2 |
| 1 | TB6612FNG | SSOP-24_5.3x8.2mm_P0.65mm | U3 |
| 2 | SN74LVC1G04DCK Texas Instruments | SOT-353_SC-70-5 | U4, U5 |
| 1 | STM32L432KCU6 STM32L432KCU STMicroelectronics | QFN-32-1EP_5x5mm_P0.5mm_EP3.45x3.45mm | U6 |
| 1 | 5V Supply | J2 | |
| 1 | Drive Motors | J3 | |
| 1 | TOF Bus | J4 | |
| 1 | TOF1 | J5 | |
| 1 | TOF2-3 | J6 | |
| 1 | Servo | J7 | |
| 1 | Push | ts04-66-xx-bk-xxx-smt-xx | SW1 |
| 7 | 100n | C_0603_1608Metric | C1, C3, C4, C5, C7, C8, C9 |
| 1 | 10u | C_0603_1608Metric | C2 |
| 1 | 4u7 | C_0603_1608Metric | C6 |
Maze bot design files
The KiCad project lives in the danielljeon/maze_bot_pcb repository on GitHub; these links point at the commit this page was built from.
- Layoutmaze_bot_pcb.kicad_pcb
- Schematicmaze_bot_pcb.kicad_sch
Maze bot: common questions
What microcontroller does the Maze bot use?
The Maze bot is built around the STM32L432KCU6, from the STM32 family.
How big is the Maze bot PCB?
The Maze bot has 4 copper layers and is 1.6062 mm thick.
How many components are on the Maze bot?
22 components, from 15 distinct parts. The full bill of materials is listed on this page.
Where can I download the Maze bot design files?
From the danielljeon/maze_bot_pcb repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Maze bot design in my own project?
The repository has no license, so all rights stay with danielljeon. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Maze bot without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k