BrakeResistor
darshp848·open-actuator-drive·hardware/brake-resistor/BrakeResistor/BrakeResistor.kicad_pcb
About the BrakeResistor PCB
BrakeResistor is an open source PCB design by darshp848, published on GitHub under the Apache-2.0 license. It is a 2-layer board measuring 190 × 38 mm, with 7 components from 4 distinct parts.
By type, the board carries 4 resistors, 2 connectors and 1 switch.
From the project
Unvalidated actuator-control PCB designs, KiCad fabrication files and board simulations
The 2.5 ohm load for the support board's brake chopper. The current Rev B layout is a 190 × 38 mm strip with four heatsinks in one row.
Mount the board flat with the heatsink fins vertical. The heatsinks have a nominal 4 mm gap between adjacent end fins. The five M3 holes and both connectors sit along the long edge.
brakesizing.py models the earlier two-by-two heatsink layout. Its output is in checks/brakesizing-output.txt.

BrakeResistor bill of materials (BOM)
7 components, 4 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XT90PW-M to support J4 | PowerWire_P8 | J1 |
| 1 | B2B-PH-K-S to support J6 (JST PH) JST | JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J2 |
| 1 | 67L085P 67L085P NC opens 85C Sensata Airpax | Airpax_67L_TO-220-2_on_RA-T2X_web | SW1 |
| 4 | LTO100F10R00JTE3 10R LTO100 Vishay Sfernice | LTO100_on_Ohmite_RA-T2X-64E | R1, R2, R3, R4 |
BrakeResistor design files
The KiCad project lives in the darshp848/open-actuator-drive repository on GitHub; these links point at the commit this page was built from.
BrakeResistor: common questions
How big is the BrakeResistor PCB?
The BrakeResistor measures 190 × 38 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the BrakeResistor?
7 components, from 4 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the BrakeResistor design files?
From the darshp848/open-actuator-drive repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the BrakeResistor design in my own project?
Yes, under the terms of its Apache-2.0 license, which darshp848 chose for the repository.
More boards in open-actuator-drive
Power split placement draft
darshp848
71.3 × 71.5 mm146 parts6LApache-2.01ACTUATOR SUPPORT BOARD - UNVALIDATED PROTOTYPE
darshp848
180 × 45 mm132 parts2LApache-2.01CapacitorBank
darshp848
101.6 × 25.4 mm15 parts2LApache-2.01DF40 Receptacle Breakout
darshp848
99.5 × 80 mm3 parts2LApache-2.01DF40 Header Breakout
darshp848
99.5 × 80 mm3 parts2LApache-2.01