SmartSense-Monitoring
DavidSPuentesc·SmartSense-Monitoring·hardware/kicad/nodo_sensor.kicad_sch
About the SmartSense-Monitoring PCB
SmartSense-Monitoring is an open source ESP32 PCB design by DavidSPuentesc, published on GitHub. It is a board, with 9 components from 9 distinct parts.
Its main chip is the XIAO ESP32-C6, from the ESP32 family. Other key parts include the Ebyte E220-433, MAX31865 (RREF 421.1) and Carga/proteccion LiPo. By type, the board carries 4 ICs, 2 resistors, 1 connector and 1 battery holder.
It belongs with the rf & radio and sensors designs in this gallery.
From the project
Proyecto académico de monitoreo industrial de temperatura con PT100, LoRa y dashboard local.
Proyecto académico de monitoreo de temperatura superficial industrial con PT100 de tres hilos, MAX31865, ESP32-C6, comunicación LoRa y consulta histórica en un dashboard local. Apoya monitoreo de condición; no implementa ni valida mantenimiento predictivo.
- SmartSenseTrabajoGrado.tex: tesis monográfica de una columna, clase report, fuera del formato IEEE. - tesis/: preliminares, diez capítulos, anexos, bibliografía autor-fecha y registro compartido datos-evidencia.tex. - hardwarex/SmartSenseHardwareX.tex: artículo HardwareX. - SmartSenseIEEE.tex: fuente histórica conservada. - figuras/…
Main components on the SmartSense-Monitoring
SmartSense-Monitoring bill of materials (BOM)
9 components, 9 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO ESP32-C6 | U1 | |
| 1 | Ebyte E220-433 | U3 | |
| 1 | MAX31865 (RREF 421.1) | U4 | |
| 1 | Carga/proteccion LiPo | U5 | |
| 1 | USB carga | J3 | |
| 1 | LiPo 3.7V 2000mAh | BT1 | |
| 1 | PT100 3 hilos | RT1 | |
| 1 | 344.8k | R1 | |
| 1 | 994.3k | R2 |
SmartSense-Monitoring design files
The KiCad project lives in the DavidSPuentesc/SmartSense-Monitoring repository on GitHub; these links point at the commit this page was built from.
SmartSense-Monitoring: common questions
What microcontroller does the SmartSense-Monitoring use?
The SmartSense-Monitoring is built around the XIAO ESP32-C6, from the ESP32 family.
How many components are on the SmartSense-Monitoring?
9 components, from 9 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the SmartSense-Monitoring design files?
From the DavidSPuentesc/SmartSense-Monitoring repository on GitHub, which has the schematic and the BOM; the links under Design files point to each one.
Can I use the SmartSense-Monitoring design in my own project?
The repository has no license, so all rights stay with DavidSPuentesc. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the SmartSense-Monitoring without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k