Fc60

developeralgo8888·fc60·hardware/fc60.kicad_pcb

Fc60 PCB layout, top view — open source Microchip SAM board by developeralgo8888

About the Fc60 PCB

Fc60 is an open source Microchip SAM PCB design by developeralgo8888, published on GitHub. It is a 2-layer board measuring 140 × 90 mm, with 226 components from 31 distinct parts.

Its main chip is the ATSAMC21N, from the Microchip SAM family. Other key parts include the MCP2542FDT-E/SN, THVD1410DGKR and LMR50410XFDBVR. By type, the board carries 69 resistors, 65 connectors, 60 transistors, 20 capacitors, 4 ICs and 2 jumpers.

From the project

60 FEEDER Controller Board

First the bootloader needs to be programmed with a suitable programmer (e.g. ATMEL-ICE, SEGGER J-Link, etc.) using the SWD-Interface J61 (10-pin 50mil connector), then the firmware can be uploaded from the mainboard. Since the MCU runs with 5V, the programmer must support this target voltage. ## How to Use The feeders are each connected using connector J1..J60 and supplied with 24V. The trigger signal is provided by a short pulse (1 ms) to the control input of the feeder. An appropriately dimensioned 24V switching power supply is connected to J64.

Fc60, from the project README
From the project README

Main components on the Fc60

ATSAMC21NMCP2542FDT-E/SNTHVD1410DGKRLMR50410XFDBVR

Fc60 bill of materials (BOM)

226 components, 31 distinct parts.

QtyPartRefs
1
ATSAMC21N
U1
1
MCP2542FDT-E/SN
U2
1
THVD1410DGKR
U3
1
LMR50410XFDBVR
U4
60
BC817
Q1, Q2, Q3, Q4, Q5, Q6, Q7, Q8 +52
60
JST XH-4
J1, J2, J3, J4, J5, J6, J7, J8 +52
1
FTSH-105-01-F-DV-K
J61
1
JST XH-3
J62
2
RJE03-166-2420
J63, J65
1
MKDS 3/4-5.08
J64
1
20A
F1
1
TERM
JP1
1
CAN RES.
JP2
1
16MHz
XTAL1
1
red
D1
1
green
D2
1
ACT1210D-510-2P-TL00
L1
1
10uH
L2
11
100n/50V
C1, C2, C3, C5, C7, C8, C9, C10 +3
2
2u2/50V
C4, C13
Show 11 more
QtyPartRefs
2
10p
C6, C11
2
100n/50V
C14, C17
2
22uF/25V
C18, C19
1
4n7/250V
C20
60
4k7
R1, R2, R3, R4, R5, R6, R7, R8 +52
1
1k
R61
2
13k
R62, R66
2
120R
R63, R64
1
52k3
R65
1
1M
R67
2
2k2
R68, R69

Fc60 design files

The KiCad project lives in the developeralgo8888/fc60 repository on GitHub; these links point at the commit this page was built from.

Fc60: common questions

What microcontroller does the Fc60 use?

The Fc60 is built around the ATSAMC21N, from the Microchip SAM family.

How big is the Fc60 PCB?

The Fc60 measures 140 × 90 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Fc60?

226 components, from 31 distinct parts. The full bill of materials is listed on this page.

Where can I download the Fc60 design files?

From the developeralgo8888/fc60 repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Fc60 design in my own project?

The repository has no license, so all rights stay with developeralgo8888. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Fc60 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Microchip SAM firmware against it before you order a PCB.

Similar boards