Droninho
dferruzzo·Droninho
About the Droninho PCB
Droninho is an open source ESP32 PCB design by dferruzzo, published on GitHub. It is a 2-layer board measuring 49 × 72.2 mm, with 32 components from 17 distinct parts.
Its main chip is the LM317MBDTG, from the ESP32 family. Other key parts include the AMS1117-3.3, LM2904M, PIC16F690-I/SS and Through Hole Connector. By type, the board carries 9 diodes, 7 ICs, 5 resistors, 4 transistors, 3 connectors and 3 capacitors.
From the project
Droninho
Este repositório apresenta um diagrama eletrônico esquemático feito em KiCad 9.0 de um drone pequeno baseado em ESP32.
- Produzir a placa de circuito impresso do hardware do droninho.
- [x] ERC OKAY! - [x] Criar PCB. - [x] Checar footprint do conectores J2, J3, J4, J5. - [x] Checar footprint do conector da bateria J1. - [x] Checar PCB rules. Corrigir footprint do MPU9250. - [x] Add connector for I2C and Power to connect other components for testing - [x] Consider connection for RC receiver (cancelled!). - [x] O MPU9250 está muito perto do ESP32 na placa. - [x] Adicionar layer com nomes dos…

Main components on the Droninho
Droninho bill of materials (BOM)
32 components, 17 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | AMS1117-3.3 Linear | SOT-223-3_TabPin2 | U1 |
| 1 | LM2904M MPU9250/6500 Fairchild | MPU-9250-6500 | U2 |
| 1 | LM317MBDTG ESP32 ESP-WROOM-32 DEVKit V1 ON | ESP32_30pin vertical WIFI | U3 |
| 1 | LM2904M Through Hole Connector Fairchild | Connector_Motor | U4 |
| 1 | PIC16F690-I/SS Through Hole Connector Microchip | Connector_Motor | U5 |
| 2 | Through Hole Connector | Connector_Motor | U6, U7 |
| 1 | GBJ10005-F Si2300DS Vishay | SOT-23 | Q1 |
| 3 | Si2300DS Vishay | SOT-23 | Q2, Q3, Q4 |
| 2 | I2C Molex | PinHeader_1x04_P2.54mm_Vertical | J6, J8 |
| 1 | TXD0/RXD0 Molex | PinHeader_1x04_P2.54mm_Vertical | J7 |
| 1 | KMR241G LFS C&K | SW_Push_1P1T_NO_CK_KMR2 | SW1 |
| 1 | RED LED Wurth Elektronik | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1 |
| 4 | WHITE LED Broadcom / Avago | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D2, D3, D4, D5 |
| 4 | 1N4148W SOD-123 SMD 100V 2A (A2) Diotec Semiconductor | D_SOD-123 | D6, D7, D8, D9 |
| 2 | 22uF/10V(20%) Murata Electronics | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2 |
| 1 | 0.1uF/10V(5%) Murata Electronics | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C3 |
| 5 | 10K(1%) Panasonic | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2, R3, R4, R5 |
Droninho design files
The KiCad project lives in the dferruzzo/Droninho repository on GitHub; these links point at the commit this page was built from.
Droninho: common questions
What microcontroller does the Droninho use?
The Droninho is built around the LM317MBDTG, from the ESP32 family.
How big is the Droninho PCB?
The Droninho measures 49 × 72.2 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Droninho?
32 components, from 17 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Droninho design files?
From the dferruzzo/Droninho repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Droninho design in my own project?
The repository has no license, so all rights stay with dferruzzo. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Droninho without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k