EmbSIM
EmbLinkOs·EmbSIM·examples/kicad-flasher/flasher.net
About the EmbSIM PCB
EmbSIM is an open source STM32 PCB design by EmbLinkOs, published on GitHub under the Apache-2.0 license. It is a board, with 10 components from 10 distinct parts.
Its main chip is the STM32F103C8Tx, from the STM32 family. Other key parts include the L7805 and NE555P. By type, the board carries 3 ICs, 3 resistors, 2 capacitors, 1 battery holder and 1 diode.
From the project
A 555 LED flasher fed from a 9 V battery through a 7805, as a KiCad netlist (flasher.net) turned into an EmbSIM project with
A 555 LED flasher fed from a 9 V battery through a 7805, as a KiCad netlist (flasher.net) turned into an EmbSIM project with
The importer maps the KiCad symbols to catalog parts with their values, keeps the net names, adds a ground symbol, and reads the 555's astable timing from R1, R2 and C1. The STM32 on the sheet is left out (an MCU belongs in a board) and reported. The probes were added by hand.
Main components on the EmbSIM
EmbSIM bill of materials (BOM)
10 components, 10 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | L7805 | TO-220-3_Vertical | U1 |
| 1 | NE555P | DIP-8_W7.62mm | U2 |
| 1 | STM32F103C8Tx | U3 | |
| 1 | 9V | BatteryHolder_Keystone_1294 | BT1 |
| 1 | LED red | D1 | |
| 1 | 10u | C1 | |
| 1 | 10n | C2 | |
| 1 | 1k | R1 | |
| 1 | 10k | R2 | |
| 1 | 330 | R3 |
EmbSIM design files
The KiCad project lives in the EmbLinkOs/EmbSIM repository on GitHub; these links point at the commit this page was built from.
EmbSIM: common questions
What microcontroller does the EmbSIM use?
The EmbSIM is built around the STM32F103C8Tx, from the STM32 family.
How many components are on the EmbSIM?
10 components, from 10 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the EmbSIM design files?
From the EmbLinkOs/EmbSIM repository on GitHub, which has a netlist and the BOM; the links under Design files point to each one.
Can I use the EmbSIM design in my own project?
Yes, under the terms of its Apache-2.0 license, which EmbLinkOs chose for the repository.
Can I test firmware for the EmbSIM without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k