Circuit GPS
About the Circuit GPS PCB
Circuit GPS is an open source AVR/Arduino PCB design by EthanSousaProjects, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 41.2 × 50.3 mm, with 3 components from 3 distinct parts.
Its main chip is the ARDUINO_NANO_ESP32, from the AVR/Arduino family. By type, the board carries 2 modules and 1 connector.
It belongs with the rf & radio designs in this gallery.
From the project
A custom cluster design for my CBR 125RW6 (2006 carb model) to replace the old large mechanical cluster with a smaller simpler design.
A custom cluster design for my CBR 125RW6 (2006 carburetor model) to replace the old large mechanical cluster with a smaller simpler design.
The references folder contains details on set things on the bike (eg. hole position dimensions, resistance of stock sensor) and thus design requirements, calculations and decisions can be found here.
There are three licenses for this project. All code falls under the AGPLV3 license, all hardware designs fall under the CERN-OHL-S license, all artwork and documentation in the READMEs related to this project are under the CC By-SA license.
Main components on the Circuit GPS
Circuit GPS bill of materials (BOM)
3 components, 3 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ARDUINO_NANO_ESP32 Arduino_Nano_v3.x | Arduino_Nano | A1 |
| 1 | GY-GPS6MV2 GPS_Module | PinSocket_1x04_P2.54mm_Vertical | M1 |
| 1 | Power_In_Connector | PinHeader_1x02_P2.54mm_Vertical | J1 |
Circuit GPS design files
The KiCad project lives in the EthanSousaProjects/CBR_Custom_Cluster repository on GitHub; these links point at the commit this page was built from.
Circuit GPS: common questions
What microcontroller does the Circuit GPS use?
The Circuit GPS is built around the ARDUINO_NANO_ESP32, from the AVR/Arduino family.
How big is the Circuit GPS PCB?
The Circuit GPS measures 41.2 × 50.3 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Circuit GPS?
3 components, from 3 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Circuit GPS design files?
From the EthanSousaProjects/CBR_Custom_Cluster repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Circuit GPS design in my own project?
Yes, under the terms of its GPL-3.0 license, which EthanSousaProjects chose for the repository.
Can I test firmware for the Circuit GPS without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
More boards in CBR_Custom_Cluster
Similar boards
AVR/ArduinoModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1k
AVR/ArduinoV4
30 × 50 mm38 parts2LCC-BY-NC-4.01.1k
AVR/ArduinoEasyduino Atmega Nano
Hanqaqa
43.4 × 18 mm30 parts4LCERN-OHL-P-2.0746
AVR/ArduinoEasyduino Atmega
68.8 × 53.6 mm35 parts4LCERN-OHL-P-2.0746
AVR/ArduinoUsbGpib
xyphro
54 × 15 mm21 parts2LMIT683
AVR/ArduinoLumberjack
peej
284.7 × 94.2 mm149 parts2LMIT402