Nt750
About the Nt750 PCB
Nt750 is an open source AVR/Arduino PCB design by evyd13, published on GitHub under the CC-BY-SA-4.0 license. It is a 2-layer board measuring 347.9 × 123.2 mm, with 199 components from 24 distinct parts.
Its main chip is the ATmega32U4, from the AVR/Arduino family. Other key parts include the USBLC6-2SC6. By type, the board carries 91 relays, 89 diodes, 6 capacitors, 5 resistors, 2 ICs and 2 connectors.
From the project
Replacement PCBs for the FC660m, FC750r and FC980m.
This is a replacement PCB for the FC750r.
Main components on the Nt750
Nt750 bill of materials (BOM)
199 components, 24 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ATmega32U4 | ATMEGA32U4 | U1 |
| 1 | USBLC6-2SC6 | USBLC6-2SC6 | U2 |
| 1 | CSTCE16M0V53-R0 | Resonator_SMD_muRata_CSTNExxV-3Pin-p1.2 | X1 |
| 1 | S5B-PH-K-S | JST_PH_S5B-PH-K_1x05_P2.00mm_Horizontal | J1 |
| 1 | ISP | isp_standard | J2 |
| 1 | 500mA, 1A | R_0805 | F1 |
| 74 | KEYSW | CHERRY_PLATE_100H | K1, K3, K4, K5, K6, K7, K8, K9 +66 |
| 1 | KEYSW | CHERRY_PCB_200H | K31 |
| 2 | KEYSW | CHERRY_PLATE_150H | K35, K48 |
| 1 | KEYSW | CHERRY_PLATE_175H | K52 |
| 2 | KEYSW | CHERRY_PCB_225H | K65, K69 |
| 1 | KEYSW | CHERRY_PCB_200H_V | K65-1 |
| 8 | KEYSW | CHERRY_PLATE_125H | K69-1, K86, K87, K88, K96, K97, K98, K99 |
| 1 | KEYSW | CHERRY_PCB_275H | K82 |
| 1 | KEYSW | CHERRY_PCB_625H_F | K92 |
| 1 | Reset | SW_SPST_TL3342 | SW1 |
| 89 | D | D_0805 | D1, D3, D4, D5, D6, D7, D8, D9 +81 |
| 1 | LED | CHERRY_MX_LED | L1 |
| 1 | 1u | C_0805 | C101 |
| 4 | 0.1u | C_0805 | C103, C104, C105, C106 |
Show 4 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 4.7u | C_0805 | C107 |
| 1 | 1k | R_0805 | R1 |
| 2 | 22 | R_0805 | R101, R102 |
| 2 | 10k | R_0805 | R104, R105 |
Nt750 design files
The KiCad project lives in the evyd13/nt-series repository on GitHub; these links point at the commit this page was built from.
- Layoutnt-750/nt750.kicad_pcb
- Schematicnt-750/nt750.kicad_sch
Nt750: common questions
What microcontroller does the Nt750 use?
The Nt750 is built around the ATmega32U4, from the AVR/Arduino family.
How big is the Nt750 PCB?
The Nt750 measures 347.9 × 123.2 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Nt750?
199 components, from 24 distinct parts. The full bill of materials is listed on this page.
Where can I download the Nt750 design files?
From the evyd13/nt-series repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Nt750 design in my own project?
Yes, under the terms of its CC-BY-SA-4.0 license, which evyd13 chose for the repository.
Can I test firmware for the Nt750 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
More boards in nt-series
Similar boards
AVR/ArduinoMagspoof
samyk
35 × 29 mm11 parts2LNo license4.2k
AVR/ArduinoRedox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0k
AVR/ArduinoLabrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2k
AVR/ArduinoModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1k
AVR/ArduinoV4
30 × 50 mm38 parts2LCC-BY-NC-4.01.1k
AVR/ArduinoDiscipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k