Backup2
FE3C61AD329B·RGT6·RGT6_core_module/backup2.kicad_pcb
About the Backup2 PCB
Backup2 is an open source STM32 PCB design by FE3C61AD329B, published on GitHub. It is a 2-layer board measuring 49.5 × 22.9 mm, with 75 components from 34 distinct parts.
Its main chip is the STM32F405RGTx, from the STM32 family. Other key parts include the MCP1703A-4002_SOT23. By type, the board carries 45 connectors, 13 resistors, 9 capacitors, 2 ICs, 2 crystals and 1 switch.
From the project
A minimal system runs MicroPython using STM32F405RGT6
A minimal system runs MicroPython using STM32F405RGT6
Designed in KiCAD, free to use in any application.
PCB preview in KiCAD Actual PCB And the size of its stencil

Main components on the Backup2
Backup2 bill of materials (BOM)
75 components, 34 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32F405RGTx | LQFP-64_10x10mm_Pitch0.5mm | U1 |
| 1 | MCP1703A-4002_SOT23 | SOT-23 | U2 |
| 1 | 8Mhz | Crystal_SMD_0603-2pin_6.0x3.5mm | Y1 |
| 1 | 32.768khz | Crystal_SMD_0603-2pin_6.0x3.5mm | Y2 |
| 1 | a3v3 | testpoint | J1 |
| 1 | USB_OTG | USB_Micro-B_Vertical_Molex-105133-0001 | J2 |
| 14 | CONN_01X01_FEMALE | testpoint | J3, J7, J8, J9, J10, J11, J12, J13 +6 |
| 1 | GND | SolderWirePad_single_0-8mmDrill | J4 |
| 8 | CONN_01X01_FEMALE | SolderWirePad_single_0-8mmDrill | J5, J6, J14, J15, J25, J26, J27, J28 |
| 4 | ADCs | testpoint | J16, J20, J21, J22 |
| 1 | do not use | testpoint | J17 |
| 4 | IOs | testpoint | J29, J30, J39, J40 |
| 2 | usart TX | SolderWirePad_single_0-8mmDrill | J31, J35 |
| 2 | usart RX | SolderWirePad_single_0-8mmDrill | J32, J36 |
| 1 | uart4 TX | SolderWirePad_single_0-8mmDrill | J33 |
| 1 | uart4 RX | SolderWirePad_single_0-8mmDrill | J34 |
| 2 | DACs | testpoint | J37, J38 |
| 3 | jtag | testpoint | J42, J43, J44 |
| 1 | SW_Push | SW_SPST_REED_CT05-XXXX-J1 | SW1 |
| 1 | WS2812B | LED_WS2812B-PLCC4 | LED1 |
Show 14 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | DIODE | D_0603 | D1 |
| 1 | 1k | L_0603 | L1 |
| 2 | 2p2 | C_0603 | C1, C2 |
| 2 | 18p | C_0603 | C3, C4 |
| 2 | 2u2 | C_0603 | C5, C6 |
| 1 | 4u7 | C_0603 | C7 |
| 1 | 100n | C_0603 | C8 |
| 1 | C | C_0603 | C9 |
| 1 | 300 | R_0603 | R1 |
| 2 | 100k | R_0603 | R2, R7 |
| 2 | 560 | R_0603 | R3, R4 |
| 2 | 22 | R_0603 | R5, R6 |
| 5 | 4k7 | R_0603 | R8, R9, R10, R11, R12 |
| 1 | 220 | R_0603 | R13 |
Backup2 design files
The KiCad project lives in the FE3C61AD329B/RGT6 repository on GitHub; these links point at the commit this page was built from.
Backup2: common questions
What microcontroller does the Backup2 use?
The Backup2 is built around the STM32F405RGTx, from the STM32 family.
How big is the Backup2 PCB?
The Backup2 measures 49.5 × 22.9 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Backup2?
75 components, from 34 distinct parts. The full bill of materials is listed on this page.
Where can I download the Backup2 design files?
From the FE3C61AD329B/RGT6 repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Backup2 design in my own project?
The repository has no license, so all rights stay with FE3C61AD329B. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Backup2 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in RGT6
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k