Nano shield
About the Nano shield
Nano shield is an open source AVR/Arduino PCB design by feastorg, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 68 × 53 mm, with 50 components from 13 distinct parts.
Its main chip is the ARDUINO_NANO_V3.X, from the AVR/Arduino family. By type, the board carries 36 connectors, 8 capacitors, 2 switches, 2 resistors, 1 module and 1 diode.
It belongs with the dev boards & breakouts designs in this gallery.
From the project
Nano-format MCU development boards designed in KiCad.
- https://wiki.dfrobot.com/ArduinoNanoIOShieldSKUDFR0012 - https://raw.githubusercontent.com/Arduinolibrary/DFRobotNanoshield/master/Nano%20Expansion%20V1.1.pdf
Main components on the Nano shield
Nano shield bill of materials (BOM)
50 components, 13 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ARDUINO_NANO_V3.X Arduino_Nano_v3.x | Arduino_Nano | A1 |
| 18 | CONN_01X04_PIN Conn_01x04_Pin | PinHeader_1x04_P2.54mm_Vertical_TightCY | J1, J2, J3, J4, J8, J9, J10, J11 +10 |
| 2 | SCREW_TERMINAL_01X02 Screw_Terminal_01x02 | TerminalBlock_4Ucon_1x02_P3.50mm_Horizontal | J5, J33 |
| 7 | CONN_01X02_PIN Conn_01x02_Pin | PinHeader_1x02_P2.54mm_Vertical_TightCY | J6, J13, J19, J22, J23, J25, J26 |
| 1 | Barrel_Jack_Switch | BarrelJack_Horizontal | J7 |
| 4 | CONN_01X08_SOCKET Conn_01x08_Socket | PinSocket_1x08_P2.54mm_Vertical_TightCY | J12, J18, J20, J29 |
| 4 | CONN_01X05_PIN Conn_01x05_Pin | PinHeader_1x05_P2.54mm_Vertical_TightCY | J21, J24, J30, J34 |
| 2 | SW_Slide_DPDT | SW_DPDT_CK_JS202011JCQN | SW1, SW2 |
| 1 | 1N4007 | D_SOD-123F | D1 |
| 7 | 0.1U 0.1u | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2, C4, C5, C6, C7, C8 |
| 1 | 47u 25V | CP_Elec_6.3x7.7 | C3 |
| 1 | 1k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1 |
| 1 | 10K 10k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2 |
Nano shield design files
The KiCad project lives in the feastorg/nano-dev-boards repository on GitHub; these links point at the commit this page was built from.
Nano shield: common questions
What microcontroller does the Nano shield use?
The Nano shield is built around the ARDUINO_NANO_V3.X, from the AVR/Arduino family.
How big is the Nano shield?
The Nano shield measures 68 × 53 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Nano shield?
50 components, from 13 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Nano shield design files?
From the feastorg/nano-dev-boards repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Nano shield design in my own project?
Yes, under the terms of its GPL-3.0 license, which feastorg chose for the repository.
Can I test firmware for the Nano shield without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
More boards in nano-dev-boards
Similar boards
AVR/ArduinoRedox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0k
AVR/ArduinoModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1k
AVR/ArduinoV4
30 × 50 mm38 parts2LCC-BY-NC-4.01.1k
AVR/ArduinoDiscipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k
AVR/ArduinoMegadesk
gcormier
41.7 × 32.2 mm23 parts2LGPL-3.0818
AVR/ArduinoEasyduino Atmega Nano
Hanqaqa
43.4 × 18 mm30 parts4LCERN-OHL-P-2.0746