Nano every
About the Nano every PCB
Nano every is an open source AVR/Arduino PCB design by feastorg, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 43.2 × 17.8 mm, with 26 components from 20 distinct parts.
Its main chip is the ATmega328P-M, from the AVR/Arduino family. Other key parts include the LM1117MP-5.0 and FT231XS. By type, the board carries 9 capacitors, 5 diodes, 4 connectors, 3 ICs, 2 resistors and 1 crystal.
It belongs with the dev boards & breakouts designs in this gallery.
From the project
Nano-format MCU development boards designed in KiCad.
Nano-format MCU development boards designed in KiCad.
The development status of various versions of the Arduino Nano V3.3 KiCAD project is indicated below:
Main components on the Nano every
Nano every bill of materials (BOM)
26 components, 20 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LM1117MP-5.0 | SOT-223-3_TabPin2 | U1 |
| 1 | FT231XS | SSOP-20_3.9x8.7mm_P0.635mm | U2 |
| 1 | ATmega328P-M | QFN-32-1EP_5x5mm_P0.5mm_EP3.1x3.1mm | U3 |
| 1 | 16MHz | Resonator_SMD_Murata_CSTxExxV-3Pin_3.0x1.1mm | Y1 |
| 1 | CONN_01X04_PIN USB_B_Micro | USB_Micro-B_Amphenol_10118193-0001LF_Horizontal | J1 |
| 2 | CONN_01X04_PIN Conn_01x15 | PinSocket_1x15_P2.54mm_Vertical | J2, J3 |
| 1 | CONN_01X04_PIN Conn_02x03_Odd_Even | PinHeader_2x03_P2.54mm_Vertical | J4 |
| 1 | PTC RESET FUSE | Fuse_0603_1608Metric_Pad1.05x0.95mm_HandSolder | F1 |
| 1 | SW_Push | SW_Push_SPST_NO_Alps_SKRK | SW1 |
| 1 | 1N4007 LED_Green_POW | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1 |
| 1 | SS1P3L | D_SMP_DO-220AA | D2 |
| 1 | LED_Red_RX | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D3 |
| 1 | LED_Green_TX | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D4 |
| 1 | LED_Orange_ONB | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D5 |
| 3 | 0.1U 1u | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C4, C7 |
| 3 | 0.1U 100n | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2, C6, C8 |
| 1 | 4.7u | CP_EIA-3216-18_Kemet-A_HandSolder | C3 |
| 1 | 0.1U 4.7u | CP_EIA-3216-18_Kemet-A_HandSolder | C5 |
| 1 | 100n | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C9 |
| 2 | 1k | R_Cat16-4 | RN1, RN2 |
Nano every design files
The KiCad project lives in the feastorg/nano-dev-boards repository on GitHub; these links point at the commit this page was built from.
Nano every: common questions
What microcontroller does the Nano every use?
The Nano every is built around the ATmega328P-M, from the AVR/Arduino family.
How big is the Nano every PCB?
The Nano every measures 43.2 × 17.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Nano every?
26 components, from 20 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Nano every design files?
From the feastorg/nano-dev-boards repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Nano every design in my own project?
Yes, under the terms of its GPL-3.0 license, which feastorg chose for the repository.
Can I test firmware for the Nano every without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
More boards in nano-dev-boards
Similar boards
AVR/ArduinoRedox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0k
AVR/ArduinoModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1k
AVR/ArduinoV4
30 × 50 mm38 parts2LCC-BY-NC-4.01.1k
AVR/ArduinoDiscipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k
AVR/ArduinoMegadesk
gcormier
41.7 × 32.2 mm23 parts2LGPL-3.0818
AVR/ArduinoEasyduino Atmega Nano
Hanqaqa
43.4 × 18 mm30 parts4LCERN-OHL-P-2.0746