Elproj-2-Grupp-11
fngksafrw·Elproj-2-Grupp-11·Schematics/Elproj2V1/Elproj2V1.kicad_sch
About the Elproj-2-Grupp-11 PCB
Elproj-2-Grupp-11 is an open source ESP32 PCB design by fngksafrw, published on GitHub under the MIT license. It is a board, with 86 components from 58 distinct parts.
Its main chip is the MOUDLE-SEEEDUINO-XIAO-ESP32C3, from the ESP32 family. Other key parts include the TPS61088RHLR and TLV61220DBVR. By type, the board carries 24 resistors, 18 capacitors, 14 connectors, 6 switches, 5 test points and 5 diodes.
From the project
Nils Kiefer Oscar Persson Isabel Serrano Nicklas Lyckman * Lucas
Main components on the Elproj-2-Grupp-11
Elproj-2-Grupp-11 bill of materials (BOM)
86 components, 58 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | MOUDLE-SEEEDUINO-XIAO-ESP32C3 | MOUDLE14P-SMD-2.54-21X17.8MM | U1 |
| 1 | TPS61088RHLR | IC_TPS61088RHLR | U2 |
| 1 | TLV61220DBVR | SOT95P280X145-6N | U3 |
| 1 | PMOS | Q1 | |
| 1 | NMOS | Q2 | |
| 5 | Conn_01x04_Pin | JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J1, J2, J3, J4, J5 |
| 1 | Conn_01x01_Pin | J6 | |
| 1 | CONN ON BUCK CARD | J7 | |
| 1 | EN | J8 | |
| 1 | Charge Boost | J9 | |
| 1 | 5V Barrel | J10 | |
| 1 | Conn_01x10_Pin | J11 | |
| 1 | CONN BUCK ON MAIN | J12 | |
| 1 | BUCK STAB CONN ON CARD | J13 | |
| 1 | BUCK CARD STAB CONN ON MAIN | J14 | |
| 1 | Jumper_2_Open | JP1 | |
| 1 | Jumper_2_Open | PinHeader_1x02_P1.00mm_Vertical | JP2 |
| 4 | Adjustable V | RV1, RV2, RV3, RV4 | |
| 5 | SW_DPDT_x2 | SW1, SW3, SW4, SW5, SW6 | |
| 1 | Manual | SW2 |
Show 38 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 3 | TP3 | TP1, TP2, TP3 | |
| 2 | ~ | TP4, TP5 | |
| 1 | D_Photo | D1 | |
| 1 | 1N914WT | D_SOD-523 | D2 |
| 1 | IR LED | D3 | |
| 1 | 6V | D4 | |
| 1 | RED LED | D5 | |
| 1 | 6.8uH | L1 | |
| 1 | Coil | L2 | |
| 1 | 680nH | L3 | |
| 1 | 2.5F | C1 | |
| 2 | 22uF | C2, C3 | |
| 1 | 470uF | C4 | |
| 2 | 4.7uF | C5, C8 | |
| 1 | 10uF | C6 | |
| 2 | 0.1uF | C7, C12 | |
| 1 | 100pF | C9 | |
| 1 | 0.01uF | C10 | |
| 1 | 0.047uF | C11 | |
| 1 | 1µF | C13 | |
| 3 | 22µF | C14, C15, C17 | |
| 1 | 1000pF | C16 | |
| 1 | Not in use | C18 | |
| 4 | 4.7k | R1, R3, R11, R12 | |
| 1 | 10k | R2 | |
| 1 | 4,7k | R4 | |
| 1 | Optional | R5 | |
| 1 | 1M | R6 | |
| 1 | R_Variable | R7 | |
| 1 | 100k | R8 | |
| 1 | 3.92k | R9 | |
| 1 | 95.3k | R10 | |
| 6 | 10 | R13, R14, R15, R22, R23, R24 | |
| 1 | 301k | R16 | |
| 1 | 56.2k | R17 | |
| 2 | R_Small | R18, R19 | |
| 1 | 49.9 | R20 | |
| 1 | 97.6 | R21 |
Elproj-2-Grupp-11 design files
The KiCad project lives in the fngksafrw/Elproj-2-Grupp-11 repository on GitHub; these links point at the commit this page was built from.
Elproj-2-Grupp-11: common questions
What microcontroller does the Elproj-2-Grupp-11 use?
The Elproj-2-Grupp-11 is built around the MOUDLE-SEEEDUINO-XIAO-ESP32C3, from the ESP32 family.
How many components are on the Elproj-2-Grupp-11?
86 components, from 58 distinct parts. The full bill of materials is listed on this page.
Where can I download the Elproj-2-Grupp-11 design files?
From the fngksafrw/Elproj-2-Grupp-11 repository on GitHub, which has the schematic; the links under Design files point to each one.
Can I use the Elproj-2-Grupp-11 design in my own project?
Yes, under the terms of its MIT license, which fngksafrw chose for the repository.
Can I test firmware for the Elproj-2-Grupp-11 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k