Bloxorz
About the Bloxorz PCB
Bloxorz is an open source PIC PCB design by FrankBuss, published on GitHub under the MIT license. It is a 2-layer board measuring 63.8 × 47.2 mm, with 24 components from 18 distinct parts.
Its main chip is the C88419, from the PIC family. Other key parts include the C485147 and C39843328. By type, the board carries 6 resistors, 4 connectors, 3 ICs, 3 capacitors, 1 crystal and 1 switch.
Main components on the Bloxorz
Bloxorz bill of materials (BOM)
24 components, 18 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | C88419 PIC16F18323 | SOIC-14_3.9x8.7mm_Pitch1.27mm | U1 |
| 1 | C485147 SST39SF040-TSOP | TSOP32WH | U2 |
| 1 | C39843328 6N135 | DIP-8_W8.89mm_SMDSocket_LongPads | U3 |
| 1 | C830041 8 MHz oscillator | oscillator | Y1 |
| 1 | C5173302 vectrex-edge-connector | vectrex | CON1 |
| 1 | PICKIT | Pin_Header_Straight_1x06_Pitch2.54mm | J1 |
| 1 | CONN_01X01_PIN DIN_5 | din5 | J4 |
| 1 | C5184243 GND | Pin_Header_Straight_1x01_Pitch2.54mm | J5 |
| 1 | C455114 SW_DPST | button | SW1 |
| 5 | 1pin | 1pin | hole1, hole2, hole3, hole4, hole5 |
| 1 | C84256 BAV99 | SOT-23_Handsoldering | D1 |
| 2 | C28323 100n | C_0805_HandSoldering | C1, C2 |
| 1 | C14663 100n | C_0805_HandSoldering | C3 |
| 1 | C25804 10k | R_0805_HandSoldering | R1 |
| 1 | 10k | R_0805_HandSoldering | R2 |
| 1 | C25804 220 | R_1206_HandSoldering | R13 |
| 1 | C25190 10k | R_0805_HandSoldering | R17 |
| 2 | C25190 220 | R_1206_HandSoldering | R18, R19 |
Bloxorz design files
The KiCad project lives in the FrankBuss/bloxorz repository on GitHub; these links point at the commit this page was built from.
- Layoutkicad/bloxorz.kicad_pcb
- Schematickicad/bloxorz.kicad_sch
- BOMprogrammer/jlcpcb-bom.xlsx
Bloxorz: common questions
What microcontroller does the Bloxorz use?
The Bloxorz is built around the C88419, from the PIC family.
How big is the Bloxorz PCB?
The Bloxorz measures 63.8 × 47.2 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Bloxorz?
24 components, from 18 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Bloxorz design files?
From the FrankBuss/bloxorz repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Bloxorz design in my own project?
Yes, under the terms of its MIT license, which FrankBuss chose for the repository.
Can I test firmware for the Bloxorz without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug PIC firmware against it before you order a PCB.
More boards in bloxorz
Similar boards
PICPslab hardware
fossasia
99 × 53.3 mm187 parts4LApache-2.01.7k
PICLens
ervanalb
80 × 80 mm53 parts4LNo license515
PICMicro 8088
skiselev
152.4 × 101.6 mm71 partsGPL-3.0414
PICGB-LIVE32
Gekkio
51.4 × 61 mm46 parts4LCC-BY-4.0376
PICGB-MBCTEST
51.4 × 61 mm32 parts2LCC-BY-4.0376
PICGB-BENCH-G1
100 × 100 mm98 parts4LCC-BY-4.0376