Panel

geezacoleman·owl-driver-board·pcb/panel.kicad_pcb

Panel PCB layout, top view — open source Raspberry Pi board by geezacoleman

About the Panel PCB

Panel is an open source Raspberry Pi PCB design by geezacoleman, published on GitHub under the MIT license. It is a 2-layer board measuring 149 × 131 mm, with 168 components from 41 distinct parts.

Its main chip is the C35165, from the Raspberry Pi family. Other key parts include the C50605, C2678753, C3210761, C12512 and C5148692. By type, the board carries 62 resistors, 41 diodes, 29 capacitors, 11 connectors, 9 ICs and 9 transistors.

From the project

Development of a board that receives GPIO input and allows on/off control of connected solenoids.

The OWL Driver Board is a solid-state relay HAT for the Raspberry Pi. It was developed for use with the Open Weed Locator but is suitable for any high-power, industrial, automotive or agricultural application.

It allows a Raspberry Pi to drive either 4x or 16x 2A outputs in any 12V or 24V system, with the solid state switching allowing PWM control, including for dimming LED strips. Outputs can be placed in parallel for more power if needed.

Panel, from the project README
From the project README

Main components on the Panel

C50605C2678753C3210761C12512C5148692

Panel bill of materials (BOM)

168 components, 41 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
C50605
TPS54531DDA
U1
1
C2678753
PCA9685PW
U2
1
C3210761
LM73100
U3
5
C12512
74LVC1G08
U4, U5, U6, U7, U8
1
C5148692
XC6206P332MR
U9
5
C17701049
AGM60P85AP
Q1, Q2, Q3, Q6, Q7
4
C8545
2N7002
Q4, Q5, Q8, Q9
1
C358686
CONN_04
J1
1
C35165
RASPBERRYPI-40-PIN-GPIO
J2
6
C3819953
1935161
J3, J4, J5, J7, J8, J10
1
C358693
CONN_04X2
J6
1
C358684
PI 5V
J9
1
C358684
ENABLE
J11
1
C207092
2920L700/12
F1
4
C207087
2920L200DR
F2, F3, F4, F5
1
C501563
SW_Coded_SH-7050
SW1
5
C434431
SZYY0805R
D1, D4, D5, D19, D20
5
C460799
BZT585B13T-7 13V
D2, D3, D6, D17, D18
1
C315992
SMBJ26A
D7
13
C727076
DSK34
D8, D9, D10, D11, D12, D13, D21, D22 +5
Show 21 more
QtyPartRefs
1
C83333
SMBJ5.0A
D16
6
C434435
SZYY0805YG
D29, D30, D31, D37, D38, D41
4
C968007
AZ23C3V3
D32, D33, D34, D35
1
C154714
PDS1040L-13
D36
5
C2987034
BZT52C5V1T
D39, D42, D43, D44, D45
1
C7461391
10uH
L1
14
C89835
10uF
C1, C2, C3, C4, C5, C10, C11, C12 +6
11
C14663
0.1uF
C6, C7, C9, C17, C21, C25, C26, C27 +3
1
C16133
100uF 6.3V
C13
1
C107107
10p
C22
1
C1870141
2n
C23
1
C77053
10n
C24
18
C21190
1k
R1, R2, R3, R4, R5, R9, R10, R13 +10
17
C25241
470
R6, R7, R17, R18, R24, R25, R26, R27 +9
21
C15401
10k
R8, R11, R12, R21, R22, R28, R32, R33 +13
1
C22816
165k
R41
1
C22772
10.2k
R42
1
C23172
43k
R43
1
C22803
14k
R44
1
C22850
1.87k
R45
1
C23146
360k
R46

Panel design files

The KiCad project lives in the geezacoleman/owl-driver-board repository on GitHub; these links point at the commit this page was built from.

Panel: common questions

What microcontroller does the Panel use?

The Panel is built around the C35165, from the Raspberry Pi family.

How big is the Panel PCB?

The Panel measures 149 × 131 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Panel?

168 components, from 41 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Panel design files?

From the geezacoleman/owl-driver-board repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.

Can I use the Panel design in my own project?

Yes, under the terms of its MIT license, which geezacoleman chose for the repository.

Can I test firmware for the Panel without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Raspberry Pi firmware against it before you order a PCB.

More boards in owl-driver-board

Similar boards