Rc car
Gingembre3005·rc-car·schematics/Schematics.kicad_sch

About the Rc car PCB
Rc car is an open source AVR/Arduino PCB design by Gingembre3005, published on GitHub. It is a board, with 8 components from 8 distinct parts.
Its main chip is the Arduino_Mega2560_R3_Shield, from the AVR/Arduino family. Other key parts include the L298N. By type, the board carries 3 modules, 2 connectors, 1 IC, 1 battery holder and 1 buzzer.
From the project
This is a RC car I made for the fifth week of the Half Life challenge by Hackclub. It's controlled by a TV Remote.
This is a RC car I made for the fifth week of the Half Life challenge by Hackclub. It's controlled by a TV Remote.
I built the car with only parts and materials I already have at home. The body of the car will be built with cardboard and wood. The steering system will be built out of Legos. You can find the electronics cost in the BOM.csv, but you should already have a lot of the building components and the TV remote.
Main components on the Rc car
Rc car bill of materials (BOM)
8 components, 8 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | L298N | MULTIWATT-15 | U1 |
| 1 | Arduino_Mega2560_R3_Shield | Arduino_Mega2560_R3_Shield | A1 |
| 1 | Motor_DC | Relay_DPDT_Schrack-RT2-FormC_RM5mm | M1 |
| 1 | Motor_DC | M2 | |
| 1 | Infrared Receiver | J1 | |
| 1 | Ultrasonic Sensor | J2 | |
| 1 | Battery | Texas_DRC0010J_ThermalVias | BT1 |
| 1 | Passive Buzzer | SOIC-8_3.9x4.9mm_P1.27mm | BZ1 |
Rc car design files
The KiCad project lives in the Gingembre3005/rc-car repository on GitHub; these links point at the commit this page was built from.
- Schematicschematics/Schematics.kicad_sch
Rc car: common questions
What microcontroller does the Rc car use?
The Rc car is built around the Arduino_Mega2560_R3_Shield, from the AVR/Arduino family.
How many components are on the Rc car?
8 components, from 8 distinct parts. The full bill of materials is listed on this page.
Where can I download the Rc car design files?
From the Gingembre3005/rc-car repository on GitHub, which has the schematic; the links under Design files point to each one.
Can I use the Rc car design in my own project?
The repository has no license, so all rights stay with Gingembre3005. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Rc car without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k