35 open source boards using the L298N

Real designs built with the L298N, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

35 boardsClear filters|Most starred

How designs wire the L298N

Read from the KiCad layouts of 22 open source designs, one per repository: what each pin of the L298N connects to, and the resistors, capacitors and other passives placed on it.

  • The VS pin has a decoupling capacitor on 9 of 21 designs, most often 100 nF (then 1 µF).
SENSE_Apin 1Connected to: GND 55% · a signal 36%
  • Resistor to GND on 36% · 1 Ω (3), 100 Ω (1), 33 Ω (1)
VSpin 4Connected to: 12V 48% · a signal 43%
  • Decoupling capacitor on 43% · 100 nF (9), 1 µF (4), 100 µF (3)
GNDpin 8Connected to: GND 86%
VSSpin 9Connected to: 5V 62% · a signal 29%
  • Decoupling capacitor on 33% · 100 nF (10), 10 µF (2), 1 µF (1)
SENSE_Bpin 15Connected to: GND 57% · a signal 38%
  • Resistor to GND on 33% · 1 Ω (3), 100 Ω (1), 33 Ω (1)

10 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Diy ert by CainPatel, Robot vacuum by dduarteCE, Two Phase Bipolar Stepper Motor Controller by Lee34667 and Atmega32 Robot by odobot.

The L298N in open source designs

The gallery holds 35 open source boards using the L298N from 28 GitHub repositories; a typical one measures about 119.8 × 92.8 mm and carries around 34 components.

82% are two-layer designs, the rest use four layers or more, and 31% carry an open source license.

The most starred is Diy ert by CainPatel.

Microcontrollers on boards using the L298N

L298N: common questions

Where can I find a L298N reference design?

Each of the 35 boards on this page is a real design using the L298N. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What decoupling capacitors do designs use on the L298N VS pin?

The VS pin has a decoupling capacitor on 9 of 21 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 22 open source designs using the L298N.

What parts are used alongside the L298N?

The AMS1117-5.0, LM7805_TO220, AMS1117-3.3, Arduino_Nano_v3.x and ATMEGA2560-16AU appear in the most repositories here.

Which microcontrollers do boards using the L298N use?

Most are built on AVR/Arduino (14), ESP32 (10), RP2040/RP2350 (2) and STM32 (1).

How big is a typical board using the L298N?

The median is 119.8 × 92.8 mm, and 82% are two-layer designs.

What is the most popular open source board using the L298N?

By GitHub stars, Diy ert by CainPatel, with 1 stars.

Can I simulate one of these boards using the L298N before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part