Tripod-Controller
GoTouchGra55·Tripod-Controller·KiCAD/Controller.kicad_pcb
About the Tripod-Controller PCB
Tripod-Controller is an open source STM32 PCB design by GoTouchGra55, published on GitHub under the MIT license. It is a 4-layer board measuring 50.5 × 64 mm, with 83 components from 41 distinct parts.
Its main chip is the STM32G474CETX, from the STM32 family. Other key parts include the LP2985-3.0, TJA1051TK-3, ICM-45686 and TPS54360DDA. By type, the board carries 36 capacitors, 23 resistors, 9 connectors, 7 ICs, 4 diodes and 2 inductors.
It belongs with the power & battery designs in this gallery.
From the project
The board handles the robot's main control electronics, providing the necessary computing capabilities for its various subsystems both planned and unplanned.
The board handles the robot's main control electronics, providing the necessary computing capabilities for its various subsystems both planned and unplanned.
2. Check for any damage on the pcb as it can be the reason for a catastrophic failure.

Main components on the Tripod-Controller
Tripod-Controller bill of materials (BOM)
83 components, 41 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32G474CETX STM32G474CETx | LQFP-48_7x7mm_P0.5mm | U1 |
| 1 | LP2985-3.0 | SOT-23-5 | U2 |
| 3 | TJA1051TK-3 | HVSON-8-1EP_3x3mm_P0.65mm_EP1.6x2.4mm | U3, U4, U6 |
| 1 | ICM-45686 | IC_ICM-45686 | U5 |
| 1 | TPS54360DDA | TI_SO-PowerPAD-8_ThermalVias | U7 |
| 1 | 8MHZ 8MHz | Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | DEBUG | JST_PH_S3B-PH-K_1x03_P2.00mm_Horizontal | J1 |
| 1 | USB_C_RECEPTACLE_USB2.0_14P USB_C_Receptacle_USB2.0_14P | USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J2 |
| 1 | CONN_01X02 Conn_01x02 | AMASS_XT60PW-M_1x02_P7.20mm_Horizontal | J3 |
| 3 | CONN_01X03_SHIELDED Conn_01x03_Shielded | JST_PH_S3B-PH-K_1x03_P2.00mm_Horizontal | J4, J5, J6 |
| 1 | CONN_01X06 Conn_01x06 | JST_PH_S6B-PH-K_1x06_P2.00mm_Horizontal | J7 |
| 1 | CONN_01X08 Conn_01x08 | JST_PH_S8B-PH-K_1x08_P2.00mm_Horizontal | J8 |
| 1 | CONN_01X03 Conn_01x03 | JST_PH_S3B-PH-K_1x03_P2.00mm_Horizontal | J9 |
| 1 | RESET | SW_Push_SPST_NO_Alps_SKRK | SW1 |
| 1 | D | Nexperia_CFP3_SOD-123W | D1 |
| 1 | B560C | Nexperia_CFP3_SOD-123W | D2 |
| 1 | RED | D_0603_1608Metric | D3 |
| 1 | GREEN | D_0603_1608Metric | D4 |
| 1 | FerriteBead | D_0603_1608Metric | FB1 |
| 1 | 8.2UH 8.2uH | L_Cenker_CKCS5040 | L1 |
Show 21 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 16 | 100NF 100nF | C_0402_1005Metric | C1, C2, C3, C4, C6, C10, C11, C12 +8 |
| 5 | 10UF 10uF | C_0603_1608Metric | C5, C14, C15, C16, C17 |
| 2 | 1UF 1uF | C_0603_1608Metric | C7, C20 |
| 2 | 20PF 20pF | C_0402_1005Metric | C8, C9 |
| 3 | 2.2UF 2.2uF | C_0603_1608Metric | C18, C31, C32 |
| 1 | 10NF 10nF | C_0402_1005Metric | C19 |
| 3 | 4.7NF 4.7nF | C_0402_1005Metric | C23, C26, C29 |
| 1 | 6.8NF 6.8nF | C_0402_1005Metric | C33 |
| 1 | 39PF 39pF | C_0402_1005Metric | C34 |
| 2 | 47UF 47uF | C_0603_1608Metric | C35, C36 |
| 2 | 5.1K | R_0603_1608Metric | R1, R2 |
| 3 | 120R | R_0603_1608Metric | R3, R6, R9 |
| 6 | 30R | R_0603_1608Metric | R4, R5, R7, R8, R10, R11 |
| 1 | 162K | R_0603_1608Metric | R12 |
| 1 | 523K | R_0603_1608Metric | R13 |
| 1 | 84.5K | R_0603_1608Metric | R14 |
| 1 | 13K | R_0603_1608Metric | R15 |
| 1 | 53.6K | R_0603_1608Metric | R16 |
| 1 | 10.2K | R_0603_1608Metric | R17 |
| 2 | 2K | R_0603_1608Metric | R18, R19 |
| 4 | R | R_0603_1608Metric | R20, R21, R22, R23 |
Tripod-Controller design files
The KiCad project lives in the GoTouchGra55/Tripod-Controller repository on GitHub; these links point at the commit this page was built from.
Tripod-Controller: common questions
What microcontroller does the Tripod-Controller use?
The Tripod-Controller is built around the STM32G474CETX, from the STM32 family.
How big is the Tripod-Controller PCB?
The Tripod-Controller measures 50.5 × 64 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Tripod-Controller?
83 components, from 41 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Tripod-Controller design files?
From the GoTouchGra55/Tripod-Controller repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Tripod-Controller design in my own project?
Yes, under the terms of its MIT license, which GoTouchGra55 chose for the repository.
Can I test firmware for the Tripod-Controller without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k