Head sensor board

hattoir·head-sensor-board

Head sensor board layout, top view — open source ESP32 board by hattoir

About the Head sensor board

Head sensor board is an open source ESP32 PCB design by hattoir, published on GitHub. It is a 2-layer board measuring 44 × 28 mm, with 30 components from 19 distinct parts.

Its main chip is the Seeed XIAO ESP32S3 Sense, from the ESP32 family. By type, the board carries 16 resistors, 4 connectors, 3 capacitors, 2 transistors, 2 diodes and 1 IC.

It belongs with the wearables, sensors and iot & wireless designs in this gallery.

From the project

Serpens Floor Watch head sensor board (prototype): VL53L1X x2 + NSSW157T x2 on XIAO ESP32S3. KiCad 10.

蛇ロボット(Serpens)Floor Watch の「頭のセンサー基板(試作用)」の KiCad プロジェクト。

- 用途: ToF の崖判定(HG-H2 の T6-1〜T6-4)と、斜め LED の追試(T4)。本番の基板ではない。 - 載せるもの: XIAO ESP32S3 Sense(ソケット)、VL53L1X 小基板 ×2(1×6 ヘッダからジャンパー線で引き出す)、白色チップ LED NSSW157T ×2(MOSFET + PWM。外付け LED 用ヘッダつき)、I2C プルアップ(未実装可)、テストポイント - 電源は既定で XIAO の 3V3 だけ。LED の電源だけ、半田ジャンパーで 5V に切り替えられる。電流の計算は docs/spec.md §4 - KiCad 10.0.1(回路図 20260306 / 基板 20260206) - バージョン管理: GitHub(プライベート hattoir/head-sensor-board)+ BoardRepo

Head sensor board, from the project README
From the project README

Main components on the Head sensor board

Seeed XIAO ESP32S3 Sense

Head sensor board bill of materials (BOM)

30 components, 19 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
Seeed XIAO ESP32S3 Sense
XIAO_ESP32S3_Sense
U1
2
AO3400A (alt. Si2302CDS)
AO3400A
Alpha & Omega (alt. Vishay)
Q1, Q2
1
PinHeader 1x06 2.54 mm
ToF_L (PLACEHOLDER)
J1
1
PinHeader 1x06 2.54 mm
ToF_R (PLACEHOLDER)
J2
1
PinHeader 1x02 2.54 mm
LED_L_EXT (1:+ 2:-)
J3
1
PinHeader 1x02 2.54 mm
LED_R_EXT (1:+ 2:-)
J4
1
solder jumper (PCB pads)
LED_L_SUPPLY
SJ1
1
solder jumper (PCB pads)
LED_R_SUPPLY
SJ2
2
NSSW157T
Nichia
D1, D2
1
ceramic capacitor 10uF
10u
C1
2
ceramic capacitor 100nF
100n
C2, C3
2
chip resistor 20 ohm
20
R1, R2
2
chip resistor 33 ohm
33
R3, R4
2
chip resistor 220 ohm
220
R5, R6
2
chip resistor 100k ohm
100k
R7, R8
2
chip resistor 1 ohm
1
R9, R10
2
chip resistor 10k ohm
10k
R11, R12
2
chip resistor 3.3k ohm
3.3k
R13, R14
2
chip resistor 0 ohm
0
R15, R16

Head sensor board design files

The KiCad project lives in the hattoir/head-sensor-board repository on GitHub; these links point at the commit this page was built from.

Head sensor board: common questions

What microcontroller does the Head sensor board use?

The Head sensor board is built around the Seeed XIAO ESP32S3 Sense, from the ESP32 family.

How big is the Head sensor board?

The Head sensor board measures 44 × 28 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Head sensor board?

30 components, from 19 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Head sensor board design files?

From the hattoir/head-sensor-board repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Head sensor board design in my own project?

The repository has no license, so all rights stay with hattoir. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Head sensor board without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards