Constellation Saddle V1.2
About the Constellation Saddle V1.2 PCB
Constellation Saddle V1.2 is an open source PCB design by HelloItzAlex, published on GitHub. It is a 2-layer board measuring 95.3 × 95.3 mm, with 29 components from 16 distinct parts.
By type, the board carries 11 connectors, 9 resistors, 4 transistors, 4 diodes and 1 capacitor.
Constellation Saddle V1.2 bill of materials (BOM)
29 components, 16 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 4 | DMP3099L | SOT-23-3 | Q1, Q2, Q3, Q4 |
| 1 | CONN_01X02_PIN Conn_01x02_Pin | SolderWire-0.75sqmm_1x02_P4.8mm_D1.25mm_OD2.3mm_Relief | J1 |
| 1 | MTJ-88ARX1-FSM-LG | ADAMTECH_MTJ-88ARX1-FSM-LG | J2 |
| 1 | 2601-1102 | CONN2_2601-1102_WAG | J3 |
| 1 | PWR | PinSocket_1x08_P2.54mm_Vertical | J4 |
| 1 | SIGNAL_OUT | CONN8_2601-1108_WAG | J5 |
| 1 | GPIO/ESP_ADC OUT | PinSocket_1x08_P2.54mm_Vertical | J6 |
| 1 | ADC_IN | PinSocket_1x08_P2.54mm_Vertical | J7 |
| 4 | 2601-1104 | CONN4_2601-1104_WAG | J8, J9, J10, J11 |
| 3 | LED | LED_0805_2012Metric | D1, D2, D3 |
| 1 | CUS10S30 | D_SOD-323 | D4 |
| 1 | 4.7UF 4.7uF | C_0805_2012Metric | C1 |
| 3 | 505 | R_0805_2012Metric | R1, R2, R9 |
| 2 | 51.1K 51.1k | R_0805_2012Metric | R3, R4 |
| 3 | 10K 10k | R_0805_2012Metric | R5, R6, R10 |
| 1 | 100 | R_0805_2012Metric | R7 |
Constellation Saddle V1.2 design files
The KiCad project lives in the HelloItzAlex/KiCAD-Designs repository on GitHub; these links point at the commit this page was built from.
Constellation Saddle V1.2: common questions
How big is the Constellation Saddle V1.2 PCB?
The Constellation Saddle V1.2 measures 95.3 × 95.3 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Constellation Saddle V1.2?
29 components, from 16 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Constellation Saddle V1.2 design files?
From the HelloItzAlex/KiCAD-Designs repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Constellation Saddle V1.2 design in my own project?
The repository has no license, so all rights stay with HelloItzAlex. Use it as a reference, and ask the author before reusing the design.
More boards in KiCAD-Designs
NI-9205 Breakout v2.0
190.5 × 279.4 mm193 parts2LNo license1
2025-2026 NI Breakout Board
190.5 × 279.4 mm193 parts2LNo license1
STM32OBC-Attempt-2 Matcha 2 Layer 1
57.2 × 101.6 mm71 parts2LNo license1
ESP32Constellation Stack V3.0
57.2 × 57.2 mm67 parts4LNo license1
STM32OBC-Attempt-1 Matcha 4 Layer
44.5 × 57.2 mm65 parts4LNo license1
STM32OBC-Attempt-5 Matcha 2 Layer 3
57.2 × 57.2 mm55 parts2LNo license1
STM32DeploymentBoardV2.0
20.3 × 31.8 mm46 parts4LNo license1
STM32Memory Board
29.9 × 38.1 mm34 parts4LNo license1
AGS Solenoid Breakout D9
50.8 × 63.5 mm18 parts2LNo license1
Load Cell Ground Systems
57.2 × 57.2 mm8 parts2LNo license1
Load Cell Ground Systems STM32
57.2 × 57.2 mm8 parts2LNo license1
Earlier revisions in the repo: Constellation Saddle V1.1, Constellation Saddle V1.0