Air ghost

HeyPCB·air-ghost·kicad/air_ghost.kicad_pcb

Air ghost PCB layout, top view — open source RISC-V board by HeyPCB

About the Air ghost PCB

Air ghost is an open source RISC-V PCB design by HeyPCB, published on GitHub under the CERN-OHL-S-2.0 license. It is a 2-layer board measuring 50.6 × 62.3 mm, with 16 components from 10 distinct parts.

Its main chip is the CH32V003F4P6, from the RISC-V family. Other key parts include the SCD40-D-R2. By type, the board carries 6 capacitors, 4 resistors, 2 ICs, 2 diodes, 1 connector and 1 switch.

It belongs with the sensors designs in this gallery.

From the project

Air Ghost: A little ghost that blushes red when your room needs fresh air. KiCad 10, heypcb.ai merch.

A little ghost that blushes red when your room needs fresh air.

Air Ghost is a desk CO2 monitor shaped like a ghost, on USB-C. A Sensirion SCD40 measures real CO2 (photoacoustic NDIR, not a VOC estimate) plus temperature and humidity every 5 s, and a CH32V003 turns the reading into the colour of the ghost's two WS2812 cheeks: green when the air is fresh, through yellow and orange to a pulsing red at 2000 ppm. Its round "O" mouth is a button: boop it for temperature and humidity colours, hold it for night mode.

Air ghost, from the project README
From the project README

Main components on the Air ghost

Air ghost bill of materials (BOM)

16 components, 10 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
CH32V003F4P6
U1
1
SCD40-D-R2
U2
1
TYPE-C-31-M-12
USB-C
J1
1
TS-1187A-B-A-B
TS-1187A
SW1
2
WS2812C-2020-V1
D1, D2
2
CL21A106KAYNNNE
10uF
C1, C3
2
CC0603KRX7R9BB104
100nF
C2, C4
2
CL05B104KO5NNNC
100nF
C5, C6
2
0402WGF5101TCE
5.1k
R1, R2
2
0402WGF1002TCE
10k
R3, R4

Air ghost design files

The KiCad project lives in the HeyPCB/air-ghost repository on GitHub; these links point at the commit this page was built from.

Air ghost: common questions

What microcontroller does the Air ghost use?

The Air ghost is built around the CH32V003F4P6, from the RISC-V family.

How big is the Air ghost PCB?

The Air ghost measures 50.6 × 62.3 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Air ghost?

16 components, from 10 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Air ghost design files?

From the HeyPCB/air-ghost repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Air ghost design in my own project?

Yes, under the terms of its CERN-OHL-S-2.0 license, which HeyPCB chose for the repository.

Can I test firmware for the Air ghost without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RISC-V firmware against it before you order a PCB.

Similar boards