17 open source boards using the SCD40-D-R2

Real designs built with the SCD40-D-R2, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

17 boardsClear filters|Most starred

How designs wire the SCD40-D-R2

Read from the KiCad layouts of 17 open source designs, one per repository: what each pin of the SCD40-D-R2 connects to, and the resistors, capacitors and other passives placed on it.

  • The VDD pins have a decoupling capacitor on 13 of 17 designs, most often 100 nF (then 10 µF).
  • The SCL pin has a pull-up to 3.3V on 12 of 17 designs, most often 10 kΩ (then 4.7 kΩ).
  • The SDA pin has a pull-up to 3.3V on 12 of 17 designs, most often 10 kΩ (then 4.7 kΩ).
DNCpin 1, 2, 3, 4, 5, 8, 11, 12, 13, 14, 15, 16, 17, 18Connected to: Not connected 100%
GNDpin 6, 20, 21Connected to: GND 94%
VDDpin 7, 19Connected to: 3.3V 76% · a signal 24%
  • Decoupling capacitor on 76% · 100 nF (31), 10 µF (5), 1 µF (2)
SCLpin 9Connected to: The microcontroller 71%, a connector 41%
  • Pull-up to 3.3V on 71% · 10 kΩ (6), 4.7 kΩ (5), 5.1 kΩ (1)
SDApin 10Connected to: The microcontroller 71%, a connector 41%
  • Pull-up to 3.3V on 71% · 10 kΩ (6), 4.7 kΩ (5), 5.1 kΩ (1)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include MiniCO2 by nup002, OpenAirScope by emertcakir, CO2 Monitor SMD by romkey and PCB Real-Time-Power-Monitoring-System-Development sensor by NguyenThanhHuy-debug.

The SCD40-D-R2 in open source designs

The gallery holds 17 open source boards using the SCD40-D-R2 from 17 GitHub repositories; a typical one measures about 80 × 56 mm and carries around 31 components.

53% are two-layer designs, the rest use four layers or more, and 47% carry an open source license.

The most starred is MiniCO2 by nup002.

Microcontrollers on boards using the SCD40-D-R2

SCD40-D-R2: common questions

Where can I find a SCD40-D-R2 reference design?

Each of the 17 boards on this page is a real design using the SCD40-D-R2. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What decoupling capacitors do designs use on the SCD40-D-R2 VDD pin?

The VDD pins have a decoupling capacitor on 13 of 17 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 17 open source designs using the SCD40-D-R2.

What pull-up resistor is used on the SCD40-D-R2 SCL pin?

The SCL pin has a pull-up to 3.3V on 12 of 17 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 17 open source designs using the SCD40-D-R2.

What pull-up resistor is used on the SCD40-D-R2 SDA pin?

The SDA pin has a pull-up to 3.3V on 12 of 17 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 17 open source designs using the SCD40-D-R2.

What parts are used alongside the SCD40-D-R2?

The USBLC6-2SC6, AMS1117-3.3, BME680, BME688 and DS3231M+TRL appear in the most repositories here.

Which microcontrollers do boards using the SCD40-D-R2 use?

Most are built on ESP32 (10), Raspberry Pi (1), RISC-V (1) and Microchip SAM (1).

How big is a typical board using the SCD40-D-R2?

The median is 80 × 56 mm, and 53% are two-layer designs.

What is the most popular open source board using the SCD40-D-R2?

By GitHub stars, MiniCO2 by nup002, with 40 stars.

Can I simulate one of these boards using the SCD40-D-R2 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part