Esp8266-for uppatvind
About the Esp8266-for uppatvind PCB
Esp8266-for uppatvind is an open source ESP8266 PCB design by horvathgergo, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 70 × 36 mm, with 27 components from 21 distinct parts.
Its main chip is the C82891, from the ESP8266 family. Other key parts include the C32078. By type, the board carries 10 resistors, 5 capacitors, 3 connectors, 3 diodes, 2 ICs and 1 switch.
From the project
Smart controller for IKEA Uppåtvind Air Purifiers
Main components on the Esp8266-for uppatvind
Esp8266-for uppatvind bill of materials (BOM)
27 components, 21 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | C32078 MC34063AD | MC34063 | U1 |
| 1 | C82891 ESP-12F | ESP-12E | U2 |
| 1 | C144395 Fan | JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J1 |
| 1 | C161869 Power | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J2 |
| 1 | UART | PinHeader_1x02_P2.54mm_Vertical | J3 |
| 2 | C318884 SW_Push | SW_SPST_SKQG_WithStem | FLASH1, RST1 |
| 1 | C255812 SW_Push | SW_Push_1P1T_NO_6x6mm_H5mm | SW1 |
| 1 | C191023 D_Schottky | D_SOD-323_HandSoldering | D1 |
| 2 | C72041 LED | LED_0603_1608Metric | D2, D3 |
| 1 | C10151 220uH | L_12x12mm_H8mm | L1 |
| 1 | C445063 100uF | CP_Elec_8x10 | C1 |
| 1 | C1743 470pF | C_0805_2012Metric_HG | C2 |
| 1 | C72518 470uF | CP_Elec_10x10.5 | C3 |
| 1 | C15850 10uF | C_0805_2012Metric_HG | C4 |
| 1 | C28233 100nF | C_0805_2012Metric_HG | C5 |
| 1 | C22787 120 | R_0603_1608Metric_HG | R1 |
| 1 | C22966 270 | R_0603_1608Metric_HG | R2 |
| 1 | C247454 0.15 | R_1206_3216Metric_Pad_HandSolder_HG | R4 |
| 1 | C22975 2K | R_0603_1608Metric_HG | R5 |
| 1 | C22978 3K3 | R_0603_1608Metric_HG | R6 |
Show 1 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 5 | C25804 10K | R_0603_1608Metric_HG | R7, R8, R9, R10, R11 |
Esp8266-for uppatvind design files
The KiCad project lives in the horvathgergo/esp8266-for-uppatvind repository on GitHub; these links point at the commit this page was built from.
Esp8266-for uppatvind: common questions
What microcontroller does the Esp8266-for uppatvind use?
The Esp8266-for uppatvind is built around the C82891, from the ESP8266 family.
How big is the Esp8266-for uppatvind PCB?
The Esp8266-for uppatvind measures 70 × 36 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Esp8266-for uppatvind?
27 components, from 21 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Esp8266-for uppatvind design files?
From the horvathgergo/esp8266-for-uppatvind repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Esp8266-for uppatvind design in my own project?
Yes, under the terms of its GPL-3.0 license, which horvathgergo chose for the repository.
Can I test firmware for the Esp8266-for uppatvind without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP8266 firmware against it before you order a PCB.
Similar boards
ESP8266ESP8266ControllerCircuit
stuartpittaway
75 × 30 mm20 parts2LCC-BY-NC-4.01.1k
ESP8266Duet WIFI
Duet3D
100 × 123 mm345 partsCERN-OHL-1.2257
ESP8266RetroWiFiModem
mecparts
100 × 66.1 mm29 parts2LGPL-3.0256
ESP8266Mideahvac dongle
reneklootwijk
20 × 48.5 mm19 parts2LNo license74
ESP8266Single radio
AnyLeaf
37.7 × 37.7 mm43 parts4LMIT63
ESP8266Tesla-Front-Drive-Unit
damienmaguire
190.5 × 176.6 mm196 parts4LNo license57