GAMEBOY STM32 CART

ice-bergtech·Icecart-GB·ICECART-GB/source/GAMEBOY_CART_STM32/GAMEBOY_STM32_CART/GAMEBOY_STM32_CART.kicad_pcb

GAMEBOY STM32 CART PCB layout, top view — open source STM32 board by ice-bergtech

About the GAMEBOY STM32 CART PCB

GAMEBOY STM32 CART is an open source STM32 PCB design by ice-bergtech, published on GitHub under the MPL-2.0 license. It is a 4-layer board measuring 51.4 × 61 mm, with 106 components from 49 distinct parts.

Its main chip is the STM32F407ZGTX, from the STM32 family. Other key parts include the HT7550, IS66WVS4M8BLL-104NLI and ES8388. By type, the board carries 51 capacitors, 29 resistors, 5 connectors, 4 ICs, 4 LEDs and 3 diodes.

It belongs with the retro computing designs in this gallery.

From the project

A ROM cartridge for the Gameboy

The power LED (+ resistor) and the bypass capacitor are optional. The value of R1 might be too high to get enough current for the LED and can be replaced with a lower value if necessary. The value is set quite high to minimize power usage and still works fine with the components I use. * All parts in the BOM can be replaced with pretty much any similar parts.

Main components on the GAMEBOY STM32 CART

GAMEBOY STM32 CART bill of materials (BOM)

106 components, 49 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
STM32F407ZGTX
STM32F407ZGTx
U1
1
HT7550
HT75xx-1-SOT89
U2
1
IS66WVS4M8BLL-104NLI
U3
1
ES8388
U4
1
AO3401A
Q1
1
PJM2319PSA
Q3
1
TAXM8M4RDBCCT2T
8MHz
Y2
1
Q13FC13500004
32.768KHz
Y3
1
DNF
J1
1
TYPE-C-31-M-12
J2
1
CONN_02X08_ODD_EVEN
Conn_02x08_Odd_Even
J4
1
Micro_SD_Card_Det
J5
1
AudioJack3_Ground
J8
2
Battery_Cell
BT1, BT2
2
SW_Push
SW1, SW2
1
Green
LD1
1
Orange
LD2
1
RED
LD3
1
Blue
LD4
2
SP0502BAHT
D1, D3
Show 29 more
QtyPartRefs
1
D_Schottky_Small
D2
2
BLM18SG121TN1D
L
FB1, L1
1
15P
10u
C1
1
15P
100n
C2
2
06035C104KAT4A
2.2uF
AVX
C3, C4
7
10u
C5, C19, C23, C33, C47, C49, C51
8
100NF
100nF
C6, C7, C8, C10, C12, C13, C14, C15
2
06035C104KAT4A
100nF
AVX
C9, C48
1
06035C104KAT4A
0.1uF
AVX
C11
1
1UF
1uF
C16
1
4.7u
C17
18
100n
C18, C20, C21, C22, C28, C29, C30, C32 +10
4
22u
C24, C25, C26, C27
1
1u
C31
4
06035C104KAT4A
22p
AVX
C34, C35, C36, C37
2
5K1
5k1
R1, R2
2
20
R3, R4
4
510
R5, R6, R7, R8
1
10K
10k
R9
5
47K
R10, R11, R13, R14, R15
2
4.7K
R12, R27
1
0
R16
3
10k
R17, R20, R28
1
4.7R
R18
1
100R
R19
3
0R
R21, R24, R29
2
33R
R22, R23
1
2K
R25
1
1K
R26

GAMEBOY STM32 CART design files

The KiCad project lives in the ice-bergtech/Icecart-GB repository on GitHub; these links point at the commit this page was built from.

GAMEBOY STM32 CART: common questions

What microcontroller does the GAMEBOY STM32 CART use?

The GAMEBOY STM32 CART is built around the STM32F407ZGTX, from the STM32 family.

How big is the GAMEBOY STM32 CART PCB?

The GAMEBOY STM32 CART measures 51.4 × 61 mm, has 4 copper layers and is 0.9912 mm thick.

How many components are on the GAMEBOY STM32 CART?

106 components, from 49 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the GAMEBOY STM32 CART design files?

From the ice-bergtech/Icecart-GB repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the GAMEBOY STM32 CART design in my own project?

Yes, under the terms of its MPL-2.0 license, which ice-bergtech chose for the repository.

Can I test firmware for the GAMEBOY STM32 CART without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

More boards in Icecart-GB

Similar boards