5 open source boards using the HT7550
Real designs built with the HT7550, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
AVR-Transistor-Tester
Upcycle-Electronics
141 × 66 mm55 parts2LNo license49RP2040/RP2350
Multislope-3I
NNNILabs
100 × 74 mm124 parts4LMIT43STM32
F405 pill
davidmolony
54.1 × 19.4 mm46 parts4LBSD-3-Clause21STM32
GAMEBOY STM32 CART
ice-bergtech
51.4 × 61 mm106 parts4LMPL-2.01STM32
F405 pill
BrMisha
54.1 × 26.6 mm74 parts4LBSD-3-Clause0
How designs wire the HT7550
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the HT7550 connects to, and the resistors, capacitors and other passives placed on it.
- The VOUT pin has a decoupling capacitor on 4 of 5 designs, most often 10 µF (then 1 µF).
- The VIN pin has a decoupling capacitor on 2 of 5 designs, most often 1 µF (then 100 nF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1 | Connected to: GND 100% | — |
| VINpin 2 | Connected to: 5V 80% · a signal 20% |
|
| VOUTpin 3 | Connected to: VCC 60% · a signal 40% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include AVR-Transistor-Tester by Upcycle-Electronics, Multislope-3I by NNNILabs, F405 pill by davidmolony and GAMEBOY STM32 CART by ice-bergtech.
The HT7550 in open source designs
The gallery holds 5 open source boards using the HT7550 from 5 GitHub repositories; a typical one measures about 54.1 × 61 mm and carries around 74 components.
80% use four copper layers or more, and 80% carry an open source license.
The most starred is AVR-Transistor-Tester by Upcycle-Electronics.
Parts used alongside the HT7550
Microcontrollers on boards using the HT7550
What boards using the HT7550 are built for
HT7550: common questions
Where can I find a HT7550 reference design?
Each of the 5 boards on this page is a real design using the HT7550. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the HT7550 VOUT pin?
The VOUT pin has a decoupling capacitor on 4 of 5 designs, most often 10 µF (then 1 µF). Counted from the KiCad layouts of 5 open source designs using the HT7550.
What decoupling capacitors do designs use on the HT7550 VIN pin?
The VIN pin has a decoupling capacitor on 2 of 5 designs, most often 1 µF (then 100 nF). Counted from the KiCad layouts of 5 open source designs using the HT7550.
What parts are used alongside the HT7550?
The LM1117-3.3, STM32F405RGTx and TCAN1051HDR appear in the most repositories here.
Which microcontrollers do boards using the HT7550 use?
Most are built on STM32 (3), AVR/Arduino (1) and RP2040/RP2350 (1).
How big is a typical board using the HT7550?
The median is 54.1 × 61 mm, and 20% are two-layer designs.
What is the most popular open source board using the HT7550?
By GitHub stars, AVR-Transistor-Tester by Upcycle-Electronics, with 49 stars.
Can I simulate one of these boards using the HT7550 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.