Yellow-Brick-Laptop-Charger
IEEE-UCR·Yellow-Brick-Laptop-Charger
About the Yellow-Brick-Laptop-Charger PCB
Yellow-Brick-Laptop-Charger is an open source PCB design by IEEE-UCR, published on GitHub under the MIT license. It is a 2-layer board measuring 80 × 60 mm, with 52 components from 34 distinct parts.
Other key parts include the LM5117*PM*. By type, the board carries 17 capacitors, 15 resistors, 9 connectors, 6 diodes, 2 transistors and 1 IC.
It belongs with the power & battery designs in this gallery.
From the project
A laptop charger that runs off of a 12S LiPo (or rather two 6S lipos)
Yellow-Brick-Laptop-Charger ===========================
Because why not charge your laptop from a giant, scary yellow brick lipo?
Design Specifics ---------------- The most important things (the soft start and such are all set to the Ti reference values) are the UVLO and output voltage divider.
The UVLO circuit is set to around 36V (3.0V per cell in a 12S configuration). It is noted that paranoid users can use a 10S lipo (which would cut off at around 3.6V per cell).
Main components on the Yellow-Brick-Laptop-Charger
Yellow-Brick-Laptop-Charger bill of materials (BOM)
52 components, 34 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LM5117*PM* | SSOP-20-1EP_4.4x6.5mm_Pitch0.65mm | U1 |
| 2 | MOS_N | PQFN-8-GDS_IRF_B_5mmx6mm | Q1, Q2 |
| 7 | TST | TP | P1, P2, P3, P4, P5, P6, P7 |
| 1 | Battery 1 | BIG_CONN | P8 |
| 1 | Power Out | BIG_CONN | P10 |
| 1 | 20A | PC_Auto_Fuse_Holder | F1 |
| 3 | DIODESCH | Diode-SMB_Standard | D1, D3, D4 |
| 1 | IN_Y | LED-0805 | D2 |
| 1 | ZENER 7.5V | Diode-SMB_Standard | D5 |
| 1 | OUT_B | LED-0805 | D6 |
| 1 | 10uH | Toroidal | L1 |
| 1 | 47pF | C_0805 | C1 |
| 7 | 1uF | C_1206 | C2, C8, C9, C10, C12, C15, C16 |
| 2 | 100nF | C_0805 | C3, C4 |
| 1 | 820pF | C_0805 | C5 |
| 1 | 5.1nF | C_0805 | C6 |
| 1 | 68pF | C_0805 | C7 |
| 1 | 100uF | c_elec_10x10 | C11 |
| 1 | 420pF | C_0805 | C13 |
| 1 | 100uF | c_elec_6.3x7.7 | C17 |
Show 14 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | NU | C_0805 | C18 |
| 1 | 100K | R_0805 | R1 |
| 1 | 3.57K | R_0805 | R2 |
| 1 | 20K | R_0805 | R3 |
| 1 | 3.9 | R_0805 | R4 |
| 1 | 31.6K | R_0805 | R5 |
| 1 | 137K | R_0805 | R6 |
| 1 | 8mohm | R_2512 | R7 |
| 1 | 10 | R_0805 | R8 |
| 1 | 22.1K | R_0805 | R9 |
| 1 | 976 | R_0805 | R10 |
| 3 | 0 | R_0805 | R11, R12, R13 |
| 1 | 5.1k | R_0805 | R14 |
| 1 | 2k | R_0805 | R15 |
Yellow-Brick-Laptop-Charger design files
The KiCad project lives in the IEEE-UCR/Yellow-Brick-Laptop-Charger repository on GitHub; these links point at the commit this page was built from.
Yellow-Brick-Laptop-Charger: common questions
How big is the Yellow-Brick-Laptop-Charger PCB?
The Yellow-Brick-Laptop-Charger measures 80 × 60 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Yellow-Brick-Laptop-Charger?
52 components, from 34 distinct parts. The full bill of materials is listed on this page.
Where can I download the Yellow-Brick-Laptop-Charger design files?
From the IEEE-UCR/Yellow-Brick-Laptop-Charger repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Yellow-Brick-Laptop-Charger design in my own project?
Yes, under the terms of its MIT license, which IEEE-UCR chose for the repository.
Similar boards
EinkPDA screen
TalismanDesign
95 × 54 mm27 parts2LApache-2.02.0kStack chan
stack-chan
50 × 50 mm33 parts2LApache-2.01.7kDisplay Carrier
AxxAxx
35.6 × 58.2 mm5 parts2LGPL-3.01.7kProgrammingAdapter
stuartpittaway
10.5 × 83 mm3 parts2LCC-BY-NC-4.01.1kTemperaturePCB PANEL
stuartpittaway
116 × 75.5 mm178 parts2LCC-BY-NC-4.01.1kModule 16S PassiveBalanceAddOn
stuartpittaway
61 × 74 mm86 parts2LCC-BY-NC-4.01.1k