Hour Meter ESP32 carrier
ilomon10·embedded-totalizer-hour-meter·schematic/hour-meter-esp32/hour-meter-esp32.kicad_pcb
About the Hour Meter ESP32 carrier PCB
Hour Meter ESP32 carrier is an open source ESP32 PCB design by ilomon10, published on GitHub. It is a 2-layer board measuring 130 × 100 mm, with 22 components from 19 distinct parts.
Its main chip is the ESP32 DevKit V1 (30-pin), from the ESP32 family. By type, the board carries 5 modules, 4 connectors, 4 diodes, 4 resistors, 3 capacitors and 1 IC.
From the project
ESP32 engine hour meter & totalizer: firmware, SensorFrame protocol, Node host tools, KiCad PCB and a Deno device simulator
A 130 × 100 mm, 2-layer, through-hole carrier board. The ESP32 DevKit and the sensor modules plug into sockets, the 817 module and the LM2596 module mount on it, and vehicle wires go to screw terminals.
Checks at release: ERC 0 errors and 0 warnings; DRC 0 errors, 0 warnings, 0 unconnected, 0 schematic mismatches; Konnect JLCPCB pre-flight READY.
The module footprints use typical clone dimensions. Check them against your parts with calipers. Open hour-meter-modules.pretty/ in the KiCad footprint editor, or edit the numbers in tools-gen-footprints.py.
Main components on the Hour Meter ESP32 carrier
Hour Meter ESP32 carrier bill of materials (BOM)
22 components, 19 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32 DevKit V1 (30-pin) | ESP32_DevKit_V1_30pin_Socket | U1 |
| 1 | 817 Module 2CH (remove G jumpers) | Module_PC817_2CH_Wired | M1 |
| 1 | DS3231 RTC module (ZS-042) | Module_DS3231_ZS042_Socket | M2 |
| 1 | AT24C256 EEPROM module (A0-A2 = GND, 0x50) | Module_AT24C256_Socket | M3 |
| 1 | MPU9250 module (AD0 = 3V3, 0x69) | Module_MPU9250_GY9250_Socket | M4 |
| 1 | LM2596 buck module (set 5.0V) | Module_LM2596_Buck | M5 |
| 1 | ALTERNATOR | TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | J1 |
| 1 | PULSE 12/24V | TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | J2 |
| 1 | UART 3.3V TTL | PinHeader_1x03_P2.54mm_Vertical | J3 |
| 1 | POWER 12/24V | TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | J4 |
| 1 | MF-R050 (60V PTC) | Fuse_Bourns_MF-RHT050 | F1 |
| 2 | 1N4007 | D_DO-41_SOD81_P10.16mm_Horizontal | D1, D2 |
| 1 | 1N5819 | D_DO-41_SOD81_P10.16mm_Horizontal | D3 |
| 1 | P6KE36CA | D_DO-15_P10.16mm_Horizontal | D4 |
| 1 | 100NF 100nF | C_Disc_D5.0mm_W2.5mm_P5.00mm | C1 |
| 1 | 1NF 1nF | C_Disc_D5.0mm_W2.5mm_P5.00mm | C2 |
| 1 | 100uF 50V | CP_Radial_D8.0mm_P3.50mm | C3 |
| 2 | 1.5k 0.5W | R_Axial_DIN0309_L9.0mm_D3.2mm_P12.70mm_Horizontal | R4, R6 |
| 2 | 47K 47k | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R5, R7 |
Hour Meter ESP32 carrier design files
The KiCad project lives in the ilomon10/embedded-totalizer-hour-meter repository on GitHub; these links point at the commit this page was built from.
Hour Meter ESP32 carrier: common questions
What microcontroller does the Hour Meter ESP32 carrier use?
The Hour Meter ESP32 carrier is built around the ESP32 DevKit V1 (30-pin), from the ESP32 family.
How big is the Hour Meter ESP32 carrier PCB?
The Hour Meter ESP32 carrier measures 130 × 100 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Hour Meter ESP32 carrier?
22 components, from 19 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Hour Meter ESP32 carrier design files?
From the ilomon10/embedded-totalizer-hour-meter repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Hour Meter ESP32 carrier design in my own project?
The repository has no license, so all rights stay with ilomon10. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Hour Meter ESP32 carrier without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k