Itaberry
InfinityCity18·itaberry·itaberry_pcb/itaberry_pcb.kicad_pcb
About the Itaberry PCB
Itaberry is an open source Raspberry Pi PCB design by InfinityCity18, published on GitHub. It is a 2-layer board measuring 35.6 × 63.2 mm, with 6 components from 5 distinct parts.
Its main chip is the RASPBERRY_PI_4, from the Raspberry Pi family.
It belongs with the displays & leds designs in this gallery.
From the project
5 displays serving as changeable/animated pins for an itabag powered by Raspberry Pi with a web interface
Itaberry bill of materials (BOM)
6 components, 5 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | RASPBERRY_PI_4 Raspberry_Pi_4 | PinHeader_2x20_P2.54mm_Vertical_SMD | J1 |
| 1 | C5160791 ST7735 128x128 8pin | PinHeader_1x08_P2.54mm_Vertical_SMD_Pin1Left | J2 |
| 2 | C5160791 GC9A01 240x240 7pin | PinHeader_1x08_P2.54mm_Vertical_SMD_Pin1Left | J3, J4 |
| 1 | C5160791 GC9A01 240x240 8pin | PinHeader_1x08_P2.54mm_Vertical_SMD_Pin1Left | J5 |
| 1 | C5160791 ST7789 240x280 8pin | PinHeader_1x08_P2.54mm_Vertical_SMD_Pin1Left | J7 |
Itaberry design files
The KiCad project lives in the InfinityCity18/itaberry repository on GitHub; these links point at the commit this page was built from.
Itaberry: common questions
What microcontroller does the Itaberry use?
The Itaberry is built around the RASPBERRY_PI_4, from the Raspberry Pi family.
How big is the Itaberry PCB?
The Itaberry measures 35.6 × 63.2 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Itaberry?
6 components, from 5 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Itaberry design files?
From the InfinityCity18/itaberry repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Itaberry design in my own project?
The repository has no license, so all rights stay with InfinityCity18. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Itaberry without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Raspberry Pi firmware against it before you order a PCB.
Similar boards
Raspberry Pi
Open source rover
nasa-jpl
220 × 178 mm144 parts2LApache-2.09.7kRaspberry Pi
Iot
dotnet
56 × 65 mm24 parts2LMIT2.4kRaspberry Pi
SPIRIT
SPIRIT-org
82 × 155 mm130 parts6LCERN-OHL-S-2.01.3kRaspberry Pi
CM5RevEng
schlae
55 × 40 mm417 parts10LNo license1.0kRaspberry Pi
Haxo hw
cardonabits
102.4 × 211.3 mm38 parts2LCustom license673Raspberry Pi
Phased
Neumi
75 × 100 mm71 parts2LNo license507