SolarNodeChargeController
jaisor·SolarNodeChargeController
About the SolarNodeChargeController PCB
SolarNodeChargeController is an open source PCB design by jaisor, published on GitHub. It is a 2-layer board measuring 56.5 × 29 mm, with 36 components from 27 distinct parts.
Other key parts include the CN3791 and INA219AID. By type, the board carries 9 connectors, 9 resistors, 7 diodes, 6 capacitors, 2 ICs and 1 transistor.
It belongs with the power & battery and rf & radio designs in this gallery.
From the project
KiCad 10 solar 1S LiPo charger: CN3791 MPPT, up to 4x 5V panels, INA219 I2C power monitor
A small solar charger board for a single-cell (1S) Li-ion/LiPo battery, built for solar-powered LoRa mesh nodes such as SNAP v1.2. Up to four 5V panels feed a CN3791 MPPT buck charger. A switched output powers the node, and an INA219 reports voltage and current over I2C.
This controller is meant for solar mesh nodes like the SNAP v1.2: Solar Node Adaptable Platform. It simplifies their build in three ways:

Main components on the SolarNodeChargeController
SolarNodeChargeController bill of materials (BOM)
36 components, 27 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | CN3791 | SSOP-10_3.9x4.9mm_P1.00mm | U1 |
| 1 | INA219AID | SOIC-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | AO3401A | SOT-23 | Q1 |
| 4 | Solar_5V | Molex_PicoBlade_53047-0210_1x02_P1.25mm_Vertical | J1, J2, J3, J4 |
| 1 | LiPo_1S_4.2V | Molex_PicoBlade_53047-0210_1x02_P1.25mm_Vertical | J5 |
| 1 | VOUT | Molex_PicoBlade_53047-0210_1x02_P1.25mm_Vertical | J6 |
| 1 | SW_BATT | Molex_PicoBlade_53047-0210_1x02_P1.25mm_Vertical | J7 |
| 1 | SW_LOAD | Molex_PicoBlade_53047-0210_1x02_P1.25mm_Vertical | J8 |
| 1 | I2C_MCU | Molex_PicoBlade_53047-0410_1x04_P1.25mm_Vertical | J9 |
| 1 | SOLAR / BATT | SW_CK_JS202011CQN_DPDT_Straight | SW3 |
| 1 | SS34 | D_SMA | D2 |
| 1 | GREEN | LED_0603_1608Metric | D3 |
| 1 | RED | LED_0603_1608Metric | D4 |
| 4 | 1N5819WS | D_SOD-323 | D5, D6, D7, D8 |
| 1 | 22uH | L_Bourns_SRN6045TA | L1 |
| 1 | 10uF/25V | C_1206_3216Metric | C1 |
| 2 | 100nF | C_0603_1608Metric | C2, C6 |
| 1 | 22uF/10V | C_1206_3216Metric | C3 |
| 1 | 220nF | C_0603_1608Metric | C4 |
| 1 | 100nF/25V | C_0603_1608Metric | C5 |
Show 7 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 1k | R_0603_1608Metric | R1 |
| 1 | 120R | R_0603_1608Metric | R2 |
| 1 | 28.0k 1% | R_0603_1608Metric | R3 |
| 1 | 10k 1% | R_0603_1608Metric | R4 |
| 1 | 0.15R 1% | R_1206_3216Metric | R5 |
| 2 | 0.1R 1% | R_1206_3216Metric | R6, R7 |
| 2 | 10k | R_0603_1608Metric | R8, R9 |
SolarNodeChargeController design files
The KiCad project lives in the jaisor/SolarNodeChargeController repository on GitHub; these links point at the commit this page was built from.
SolarNodeChargeController: common questions
How big is the SolarNodeChargeController PCB?
The SolarNodeChargeController measures 56.5 × 29 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the SolarNodeChargeController?
36 components, from 27 distinct parts. The full bill of materials is listed on this page.
Where can I download the SolarNodeChargeController design files?
From the jaisor/SolarNodeChargeController repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the SolarNodeChargeController design in my own project?
The repository has no license, so all rights stay with jaisor. Use it as a reference, and ask the author before reusing the design.
Similar boards
EinkPDA screen
TalismanDesign
95 × 54 mm27 parts2LApache-2.02.0kStack chan
stack-chan
50 × 50 mm33 parts2LApache-2.01.7kDisplay Carrier
AxxAxx
35.6 × 58.2 mm5 parts2LGPL-3.01.7kProgrammingAdapter
stuartpittaway
10.5 × 83 mm3 parts2LCC-BY-NC-4.01.1kTemperaturePCB PANEL
stuartpittaway
116 × 75.5 mm178 parts2LCC-BY-NC-4.01.1kModule 16S PassiveBalanceAddOn
stuartpittaway
61 × 74 mm86 parts2LCC-BY-NC-4.01.1k