Autonomous drone
jeffmc6767·Autonomous-drone·PCB/FCPCB.kicad_pcb
About the Autonomous drone PCB
Autonomous drone is an open source STM32 PCB design by jeffmc6767, published on GitHub. It is a 4-layer board measuring 36.7 × 35.2 mm, with 34 components from 22 distinct parts.
Its main chip is the STM32F411CEUx, from the STM32 family. Other key parts include the BMI270, TPS54302 and AP2127K-3.3. By type, the board carries 15 capacitors, 8 resistors, 4 ICs, 3 connectors, 3 diodes and 1 inductor.
It belongs with the robotics & motion and rf & radio designs in this gallery.
From the project
JFC, - My custom 20x20 drone FC stack for 4s setups, and my custom 3 inch drone frame.
JFC, - My custom 20x20 drone FC stack for 4s setups, and my custom 3 inch drone frame.
FOR THE STARDANCE REVIEWS: I submitted this a long time ago I dont remember if I said in the note. In my KICAD schematic the wiring is all on the LEFT side. Just zoom out and you can see everything. Specs: -
- up to 99km/h (I calculated based on other drones with similar setup and weight) - A theoretical 5-7 minutes of flight time though im not sure - Costs around 1.2$ a print and tees 3.5 hours. - 4K video 60fps (from the dji o4 air unit) - Usable with Ardu pilot, betafpv, and most other open source…
Main components on the Autonomous drone
Autonomous drone bill of materials (BOM)
34 components, 22 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | BMI270 | BMI270 | IC3 |
| 1 | TPS54302 | SOT-23-6 | U4 |
| 1 | STM32F411CEUx | QFN-48-1EP_7x7mm_P0.5mm_EP5.6x5.6mm | U5 |
| 1 | AP2127K-3.3 | SOT-23-5 | U6 |
| 1 | Conn_01x06 | JST_SH_SM06B-SRSS-TB_1x06-1MP_P1.00mm_Horizontal | J5 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J6 |
| 1 | Conn_01x08 | JST_SH_SM08B-SRSS-TB_1x08-1MP_P1.00mm_Horizontal | J49 |
| 2 | LED | LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1, D2 |
| 1 | D_Schottky | D_SOD-123 | D5 |
| 1 | 10μH | L_Coilcraft_XAL4020-XXX | L3 |
| 1 | 10µF | C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C24 |
| 8 | 100nF | C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C25, C32, C33, C34, C35, C38, C39, C87 |
| 1 | 22µF | C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C28 |
| 1 | 22µF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C29 |
| 2 | 1µF | C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C30, C31 |
| 1 | 4.7µF | C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C36 |
| 1 | 2.2µF | C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C37 |
| 2 | 1 kΩ | R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R2, R3 |
| 1 | 10k | R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R18 |
| 1 | 73.2k | R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R19 |
Show 2 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 10kΩ | R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R20, R21 |
| 2 | 5.1kΩ | R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R22, R23 |
Autonomous drone design files
The KiCad project lives in the jeffmc6767/Autonomous-drone repository on GitHub; these links point at the commit this page was built from.
- LayoutPCB/FCPCB.kicad_pcb
- SchematicPCB/FCPCB.kicad_sch
Autonomous drone: common questions
What microcontroller does the Autonomous drone use?
The Autonomous drone is built around the STM32F411CEUx, from the STM32 family.
How big is the Autonomous drone PCB?
The Autonomous drone measures 36.7 × 35.2 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Autonomous drone?
34 components, from 22 distinct parts. The full bill of materials is listed on this page.
Where can I download the Autonomous drone design files?
From the jeffmc6767/Autonomous-drone repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Autonomous drone design in my own project?
The repository has no license, so all rights stay with jeffmc6767. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Autonomous drone without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k