Drone ESC Bridge

jerinabr·Drone_ESC_Bridge

Drone ESC Bridge PCB layout, top view — open source board by jerinabr

About the Drone ESC Bridge PCB

Drone ESC Bridge is an open source PCB design by jerinabr, published on GitHub. It is a 2-layer board measuring 52 × 33 mm, with 22 components from 15 distinct parts.

Other key parts include the 296-48927-1-ND and 296-46427-1-ND. By type, the board carries 8 capacitors, 4 resistors, 2 ICs and 1 transistor.

It belongs with the robotics & motion and power & battery designs in this gallery.

From the project

PCB that allows the NVIDIA Jetson to communicate with the 4-in-1 ESC for the drone

It recieves motor speeds and other commands from the Jetson over the SPI interface and outputs motor speeds to the ESC over PWM

It also monitors the LiPo voltage and can report it back to the Jetson over the SPI interface

The board receives 5V power from an off-board buck converter which is used to power both the microcontroller (Seeed XIAO SAMD21) and the Jetson

Drone ESC Bridge, from the project README
From the project README

Main components on the Drone ESC Bridge

296-48927-1-ND296-46427-1-ND

Drone ESC Bridge bill of materials (BOM)

22 components, 15 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
296-48927-1-ND
LMP8640
U1
1
296-46427-1-ND
LM5050-1
U2
1
SI2318CDS-T1-GE3CT-ND
Si2318CDS
Q1
1
455-BM08B-SRSS-TBCT-ND
Conn_01x08
ESC1
1
2057-PH2-06-UA-ND
Conn_01x06
ESC_DEBUG1
1
2057-PH2-04-UA-ND
Conn_02x02_Top_Bottom
JETSON_PWR1
2
2057-PH2-04-UA-ND
Conn_01x04
SPI1, VBUCK1
2
S7040-ND
Conn_01x07
XIAO_L1, XIAO_R1
6
311-1088-1-ND
0.1u
C1, C2, C4, C6, C7, C8
1
311-1446-1-ND
1u
C3
1
PCE3811CT-ND
22u
C5
1
13-PE2010FKE070R01LCT-ND
10m
R1
1
311-100HRCT-ND
100
R2
1
311-33.0KHRTR-ND
33k
R3
1
311-8.2KGRTR-ND
8.2k
R4

Drone ESC Bridge design files

The KiCad project lives in the jerinabr/Drone_ESC_Bridge repository on GitHub; these links point at the commit this page was built from.

Drone ESC Bridge: common questions

How big is the Drone ESC Bridge PCB?

The Drone ESC Bridge measures 52 × 33 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Drone ESC Bridge?

22 components, from 15 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Drone ESC Bridge design files?

From the jerinabr/Drone_ESC_Bridge repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Drone ESC Bridge design in my own project?

The repository has no license, so all rights stay with jerinabr. Use it as a reference, and ask the author before reusing the design.

Similar boards