Upd78c14-pico reader

jj-0·upd78c14-pico-reader·hw/upd78c14-pico-reader.kicad_sch

This repository ships a schematic but no board layout.

About the Upd78c14-pico reader PCB

Upd78c14-pico reader is an open source RP2040/RP2350 PCB design by jj-0, published on GitHub under the MIT license. It is a board, with 30 components from 6 distinct parts.

Its main chip is the Raspberry Pi Pico 2, from the RP2040/RP2350 family. Other key parts include the uPD78C14GF (QFP64->DIP64 900mil adapter) and 74HCT04. By type, the board carries 24 resistors, 3 capacitors, 2 ICs and 1 module.

It belongs with the dev boards & breakouts designs in this gallery.

From the project

Dump the NEC uPD78C14 mask ROM (PC Engine Duo) with a Raspberry Pi Pico 2 - firmware, KiCad schematic, breadboard build

Dumps the 16 KB internal mask ROM of the NEC µPD78C14GF (the 64-pin QFP in the PC Engine Duo). It also works for the µPD7811 / 78C11 (4 KB), 78C12 (8 KB) and 78C18 (32 KB).

This is a port of https://github.com/devinacker/upd7811-reader (v1.0) to a Pico 2. The upstream firmware that runs on the NEC chip is reused unchanged (upstream/upd7811-reader.bin, embedded as readerrom.h`). The Pico takes over the jobs of the upstream board's parts:

Main components on the Upd78c14-pico reader

uPD78C14GF (QFP64->DIP64 900mil adapter)74HCT04Raspberry Pi Pico 2

Upd78c14-pico reader bill of materials (BOM)

30 components, 6 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
uPD78C14GF (QFP64->DIP64 900mil adapter)
U1
1
74HCT04
U2
1
Raspberry Pi Pico 2
A1
3
100nF
C1, C2, C3
23
22k
R1, R2, R3, R4, R5, R6, R7, R8 +15
1
4.7k
R24

Upd78c14-pico reader design files

The KiCad project lives in the jj-0/upd78c14-pico-reader repository on GitHub; these links point at the commit this page was built from.

Upd78c14-pico reader: common questions

What microcontroller does the Upd78c14-pico reader use?

The Upd78c14-pico reader is built around the Raspberry Pi Pico 2, from the RP2040/RP2350 family.

How many components are on the Upd78c14-pico reader?

30 components, from 6 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Upd78c14-pico reader design files?

From the jj-0/upd78c14-pico-reader repository on GitHub, which has the schematic, a netlist and the BOM; the links under Design files point to each one.

Can I use the Upd78c14-pico reader design in my own project?

Yes, under the terms of its MIT license, which jj-0 chose for the repository.

Can I test firmware for the Upd78c14-pico reader without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.

Similar boards