KiCad
JLimbocker·KiCad·BC/BC.kicad_pcb
About the KiCad PCB
KiCad is an open source TI MSP430/CC PCB design by JLimbocker, published on GitHub. It is a 2-layer board measuring 176.5 × 82.6 mm, with 80 components from 11 distinct parts.
Its main chip is the MSP430G2203IPW28, from the TI MSP430/CC family. Other key parts include the DS3231N and AP1117. By type, the board carries 42 resistors, 16 transistors, 13 diodes, 3 ICs, 3 capacitors and 1 connector.
Main components on the KiCad
KiCad bill of materials (BOM)
80 components, 11 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | DS3231N | SO-16-L | U1 |
| 1 | MSP430G2203IPW28 | SOIC-28 | U2 |
| 1 | AP1117 | SOT-23-5 | U3 |
| 3 | Q_NMOS_GSD | SOT-23 | Q1, Q2, Q5 |
| 13 | Q_PMOS_GSD | SOT-23 | Q3, Q4, Q6, Q7, Q8, Q9, Q10, Q11 +5 |
| 1 | BARREL_JACK | Pin_Header_Straight_1x02 | CON1 |
| 1 | Battery | Banana_Jack_2Pin | BT1 |
| 1 | SW_PUSH | SW_SPST_FSMSM | SW1 |
| 13 | LED_RGB | LED_RGB_PLLC-6 | D1, D2, D3, D4, D5, D6, D7, D8 +5 |
| 3 | C | C_0805_HandSoldering | C1, C2, C3 |
| 42 | R | R_0805_HandSoldering | R1, R2, R3, R4, R5, R6, R7, R8 +34 |
KiCad design files
The KiCad project lives in the JLimbocker/KiCad repository on GitHub; these links point at the commit this page was built from.
- LayoutBC/BC.kicad_pcb
KiCad: common questions
What microcontroller does the KiCad use?
The KiCad is built around the MSP430G2203IPW28, from the TI MSP430/CC family.
How big is the KiCad PCB?
The KiCad measures 176.5 × 82.6 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the KiCad?
80 components, from 11 distinct parts. The full bill of materials is listed on this page.
Where can I download the KiCad design files?
From the JLimbocker/KiCad repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the KiCad design in my own project?
The repository has no license, so all rights stay with JLimbocker. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the KiCad without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug TI MSP430/CC firmware against it before you order a PCB.
Similar boards
TI MSP430/CC
Pluto
carrotIndustries
24.4 × 24.4 mm36 parts2LGPL-3.0536TI MSP430/CC
Apimote
riverloopsec
83.3 × 33.4 mm80 parts4LTAPR-OHL-1.089TI MSP430/CC
Toniebox
toniebox-reverse-engineering
88 × 102 mm11 parts2LNo license36TI MSP430/CC
Nsumo hardware
artfulbytes
50 × 65 mm73 parts2LMIT33TI MSP430/CC
Elektronika-1
BenjaminSoelberg
29.5 × 29.5 mm14 parts4LGPL-3.029TI MSP430/CC
MSP430 Breadstick - Apple Sauce
upsidedownlabs
18.5 × 65.8 mm31 parts2LCERN-OHL-S-2.021