SimpleCANBreakout
jlpoltrack·SimpleCANBreakout
About the SimpleCANBreakout PCB
SimpleCANBreakout is an open source PCB design by jlpoltrack, published on GitHub under the MIT license. It is a 2-layer board measuring 31.5 × 15.5 mm, with 9 components from 5 distinct parts.
Other key parts include the SN65HVD230 and AMS1117-3.3. By type, the board carries 6 capacitors, 2 ICs and 1 resistor.
It belongs with the rf & radio and dev boards & breakouts designs in this gallery.
From the project
31.5x15.5 mm TCAN332 CAN transceiver breakout with solder pads (KiCad)
A small (31.5 × 15.5 mm) CAN transceiver breakout. It converts a microcontroller's logic-level CAN TX/RX to a CAN bus, with an onboard 3.3 V regulator and 120 Ω termination. All connections are large solder pads, so wires can be soldered directly to the board.
Designed in KiCad 10. See SimpleCANBreakoutMicro for a smaller version with a JST-GH connector, an XC6206 regulator, and switchable termination.

Main components on the SimpleCANBreakout
SimpleCANBreakout bill of materials (BOM)
9 components, 5 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | SN65HVD230 | SOIC-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U2 |
| 3 | 10U 10u | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C4, C6 |
| 3 | 100N 100n | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2, C3, C5 |
| 1 | 120 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1 |
SimpleCANBreakout design files
The KiCad project lives in the jlpoltrack/SimpleCANBreakout repository on GitHub; these links point at the commit this page was built from.
- LayoutSimpleCANBreakout.kicad_pcb
- SchematicSimpleCANBreakout.kicad_sch
- BOMproduction/bom.csv
SimpleCANBreakout: common questions
How big is the SimpleCANBreakout PCB?
The SimpleCANBreakout measures 31.5 × 15.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the SimpleCANBreakout?
9 components, from 5 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the SimpleCANBreakout design files?
From the jlpoltrack/SimpleCANBreakout repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the SimpleCANBreakout design in my own project?
Yes, under the terms of its MIT license, which jlpoltrack chose for the repository.
Similar boards
Breakout 112pin Connector
rusefi
174 × 58 mm39 parts2LGPL-3.01.2kEecv breakout
rusefi
140.8 × 53.7 mm9 parts4LGPL-3.01.2kBreakout 60pin EEC-IV
rusefi
139.7 × 62.2 mm15 parts2LGPL-3.01.2k134pin 7-967288-1
rusefi
139.7 × 73.7 mm38 parts2LGPL-3.01.2k88 Pin Vag Breakout
rusefi
142 × 58 mm91 parts2LGPL-3.01.2kRj45 breakout
rene-dev
15.2 × 53.8 mm3 parts2LGPL-3.0979