QuadrupedTurret
JoelBiswas·QuadrupedTurret·KiCad/QudrupedTurret.kicad_sch
About the QuadrupedTurret PCB
QuadrupedTurret is an open source ESP32 PCB design by JoelBiswas, published on GitHub. It is a board, with 16 components from 15 distinct parts.
It is laid out to mount a board from the ESP32 family. By type, the board carries 12 modules, 2 transistors, 1 IC and 1 battery holder.
It belongs with the robotics & motion, power & battery and iot & wireless designs in this gallery.
From the project
Four-legged robot with a turret mounted to the top. Created for Hack Club Highway to Undercity
Subtotal: $156.65 Taxes (4%): $6.27 Total: $162.92
QuadrupedTurret bill of materials (BOM)
16 components, 15 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ~ | U1 | |
| 1 | Base_Servo_Front_Right | M1 | |
| 1 | Base_Servo_Front_Left | M2 | |
| 1 | Base_Servo_Back_Left | M3 | |
| 1 | Base_Servo_Back_Right | M4 | |
| 1 | Knee_Servo_Front_Right | M5 | |
| 1 | Knee_Servo_Front_Left | M6 | |
| 1 | Knee_Servo_Back_Left | M7 | |
| 1 | Knee_Servo_Back_Right | M8 | |
| 1 | Pitch_Servo | M9 | |
| 1 | Reloading_Servo | M10 | |
| 1 | Flywheel_Motor_Left | M11 | |
| 1 | Flywheel_Motor_Right | M12 | |
| 2 | BC107 | TO-18-3 | Q1, Q2 |
| 1 | Battery | BT1 |
QuadrupedTurret design files
The KiCad project lives in the JoelBiswas/QuadrupedTurret repository on GitHub; these links point at the commit this page was built from.
- SchematicKiCad/QudrupedTurret.kicad_sch
- BOMBOM.csv
QuadrupedTurret: common questions
How many components are on the QuadrupedTurret?
16 components, from 15 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the QuadrupedTurret design files?
From the JoelBiswas/QuadrupedTurret repository on GitHub, which has the schematic and the BOM; the links under Design files point to each one.
Can I use the QuadrupedTurret design in my own project?
The repository has no license, so all rights stay with JoelBiswas. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the QuadrupedTurret without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k