HCP-Bridge
JonasE99·HCP-Bridge·hardware/kicad/HCPBridge.kicad_pcb
About the HCP-Bridge PCB
HCP-Bridge is an open source ESP32 PCB design by JonasE99, published on GitHub. It is a 2-layer board measuring 36 × 72 mm, with 45 components from 28 distinct parts.
Its main chip is the Espressif ESP32-S3-WROOM-1-N8R2, from the ESP32 family. Other key parts include the TI LMR51610XDBVR and TI THVD1406DR. By type, the board carries 16 resistors, 10 diodes, 10 capacitors, 3 ICs, 2 connectors and 2 switches.
It belongs with the iot & wireless and rf & radio designs in this gallery.
From the project
🚧 WIP – not yet manufactured or tested. KiCad PCB (one per door) connecting Hörmann series 4 garage door operators (ProMatic/SupraMatic, BUS/RJ12) to Loxone via ESP32-S3 and Wi-Fi. Hardware only – intended to run the existing HCPBridgeMqtt firmware by Gifford47.
A small board (one per door) that plugs into the BUS port (RJ12) of a Hörmann series 4 garage door operator (ProMatic 4, SupraMatic E/P 4). It acts as a UAP1-HCP expansion module towards the operator and exposes the door via Wi-Fi. Loxone talks to it over plain HTTP, no extra server needed (see below).
Firmware: This repository contains the hardware only. The board is meant to run the existing third-party open-source firmware HCPBridgeMqtt by Gifford47 (environment HCPGiffordv2`, provides web UI, HTTP API and MQTT). The board uses the same pins as the original ESP32-S3 boards, so the…

Main components on the HCP-Bridge
HCP-Bridge bill of materials (BOM)
45 components, 28 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TI LMR51610XDBVR LMR51610XDBVR | SOT-23-6 | U1 |
| 1 | TI THVD1406DR THVD1406DR | SOIC-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | Espressif ESP32-S3-WROOM-1-N8R2 ESP32-S3-WROOM-1-N8R2 | ESP32-S3-WROOM-1 | U3 |
| 1 | Molex 95501-2661 RJ12 HCP bus | RJ12_Molex_95501-2661_Horizontal | J1 |
| 1 | HRO TYPE-C-31-M-12 USB-C | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J2 |
| 1 | BSMD1206-020-48V 200mA | Fuse_1206_3216Metric | F1 |
| 1 | XKB TS-1187A-B-A-B RESET | SW_Push_1P1T_XKB_TS-1187A | SW1 |
| 1 | XKB TS-1187A-B-A-B BOOT | SW_Push_1P1T_XKB_TS-1187A | SW2 |
| 1 | SMAJ33CA (bidirectional) SMAJ33CA | D_SMA | D1 |
| 5 | DSS16 (60 V, 1 A) DSS16 | D_SOD-123 | D2, D3, D4, D5, D6 |
| 1 | KT-0603G green | LED_0603_1608Metric | D7 |
| 1 | Semtech SM712.TCT SM712 | SOT-23 | D8 |
| 1 | KT-0603B blue | LED_0603_1608Metric | D9 |
| 1 | ST USBLC6-2SC6 USBLC6-2SC6 | SOT-23-6 | D10 |
| 1 | Bourns SRN5040TA-220M (Isat 1.62 A) 22uH | L_Sunlord_SWPA5040S | L1 |
| 2 | C170101 2u2 100V | C_1206_3216Metric | C1, C2 |
| 4 | 100N 100n | C_0603_1608Metric | C3, C6, C8, C9 |
| 3 | C77091 22u 25V | C_1206_3216Metric | C4, C5, C7 |
| 1 | 1u | C_0603_1608Metric | C10 |
| 1 | 0603WAF1003T5E 100k | R_0603_1608Metric | R1 |
Show 8 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | C23098 69k8 1% | R_0603_1608Metric | R2 |
| 1 | C137768 22k1 1% | R_0603_1608Metric | R3 |
| 2 | 0603WAF1001T5E 1k | R_0603_1608Metric | R4, R14 |
| 2 | 10R | R_0603_1608Metric | R5, R6 |
| 2 | 0603WAF4701T5E 4k7 | R_0603_1608Metric | R7, R8 |
| 1 | 120R | R_0603_1608Metric | R9 |
| 4 | Yageo RC0603FR-0710KL 10k | R_0603_1608Metric | R10, R11, R12, R13 |
| 2 | 0603WAF5101T5E 5k1 | R_0603_1608Metric | R15, R16 |
HCP-Bridge design files
The KiCad project lives in the JonasE99/HCP-Bridge repository on GitHub; these links point at the commit this page was built from.
HCP-Bridge: common questions
What microcontroller does the HCP-Bridge use?
The HCP-Bridge is built around the Espressif ESP32-S3-WROOM-1-N8R2, from the ESP32 family.
How big is the HCP-Bridge PCB?
The HCP-Bridge measures 36 × 72 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the HCP-Bridge?
45 components, from 28 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the HCP-Bridge design files?
From the JonasE99/HCP-Bridge repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the HCP-Bridge design in my own project?
The repository has no license, so all rights stay with JonasE99. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the HCP-Bridge without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k