BIOT Node 0 .4
jonkster·biot·hardware/biot_node_0.4/biot-node.kicad_pcb
About the BIOT Node 0 .4 PCB
BIOT Node 0 .4 is an open source Microchip SAM PCB design by jonkster, published on GitHub under the MIT license. It is a 2-layer board measuring 98 × 84.1 mm, with 13 components from 12 distinct parts.
Its main chip is the ATSAMR21B, from the Microchip SAM family. Other key parts include the MPU9250-Breakout. By type, the board carries 5 connectors, 3 resistors, 2 diodes, 1 IC, 1 battery holder and 1 switch.
From the project
Code for simple biot nodes.
Biot node hardware/schematics etc. These files are for KiCAD The PCB layouts and design are very amateurish, sorry - I am learning as I am going. Feel free to use anyhing here but you could probably design better ones yourself.
Main components on the BIOT Node 0 .4
BIOT Node 0 .4 bill of materials (BOM)
13 components, 12 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | MPU9250-Breakout | Pin_Header_Straight_1x10 | U1 |
| 1 | ATSAMR21B | Pin_Header_Straight_1x07_Pitch2.00mm | P1 |
| 1 | ATSAMR21B-TEST-POINTs | Pin_Header_Straight_1x05 | P2 |
| 1 | ATMEL-CORTEX | ATMEL_cortex_header_smd | P3 |
| 1 | FTDI/Serial | Pin_Header_Straight_1x06 | P4 |
| 1 | On/Off Header | Pin_Header_Straight_1x03 | P5 |
| 1 | 1.5V | Pin_Header_Straight_1x02 | BT1 |
| 1 | RESET | SW_SPST_EVPBF | SW1 |
| 1 | SIGNAL | LED_1206 | D1 |
| 1 | PWR | LED_1206 | D2 |
| 1 | 10k | R_1210 | R1 |
| 2 | 39 | R_1210 | R2, R3 |
BIOT Node 0 .4 design files
The KiCad project lives in the jonkster/biot repository on GitHub; these links point at the commit this page was built from.
BIOT Node 0 .4: common questions
What microcontroller does the BIOT Node 0 .4 use?
The BIOT Node 0 .4 is built around the ATSAMR21B, from the Microchip SAM family.
How big is the BIOT Node 0 .4 PCB?
The BIOT Node 0 .4 measures 98 × 84.1 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the BIOT Node 0 .4?
13 components, from 12 distinct parts. The full bill of materials is listed on this page.
Where can I download the BIOT Node 0 .4 design files?
From the jonkster/biot repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the BIOT Node 0 .4 design in my own project?
Yes, under the terms of its MIT license, which jonkster chose for the repository.
Can I test firmware for the BIOT Node 0 .4 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Microchip SAM firmware against it before you order a PCB.
More boards in biot
Similar boards
Microchip SAM
Microcontroller Expansion Card
FrameworkComputer
26 × 30 mm24 parts2LCC-BY-4.01.1kMicrochip SAM
Taco Raven
VoronDesign
120 × 113 mm349 parts4LGPL-3.01.1kMicrochip SAM
Fpgaboy
Wren6991
50 × 50 mm89 parts4LNo license511Microchip SAM
OpenDropV4
GaudiLabs
124 × 115.4 mm118 parts2LGPL-3.0487Microchip SAM
ModulAdapter universal
GaudiLabs
100 × 69.5 mm45 parts2LGPL-3.0487Microchip SAM
Kira
kiibohd
366.9 × 114.3 mm400 partsCERN-OHL-1.2416