HardLabs

Rpi ibex hyperpixel

jovan3·rpi-ibex-hyperpixel

Rpi ibex hyperpixel PCB layout, top view — open source AVR/Arduino board by jovan3

About the Rpi ibex hyperpixel PCB

Rpi ibex hyperpixel is an open source AVR/Arduino PCB design by jovan3, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 99.1 × 113.5 mm, with 32 components from 18 distinct parts.

Its main chip is the ATmega328PB-AU, from the AVR/Arduino family. By type, the board carries 4 connectors, 3 capacitors, 2 ICs, 2 crystals, 1 module and 1 transistor.

It belongs with the displays & leds designs in this gallery.

From the project

Portable Raspberry Pi Zero based computer with a Hyperpixel display

RPi Ibex is a Raspberry Pi Zero based portable computer. The goal of the project is to provide a way to use Raspberry Pi Zero as a portable computer using parts that are available, cheap and relatively easy to solder (no exotic keyboard controller chips required).

This repository contains Kicad project files for the PCB. The keyboard is just simple push buttons soldered directly on the board. The keyboard controller is an Atmega 328P.

Rpi ibex hyperpixel, from the project README
From the project README

Main components on the Rpi ibex hyperpixel

ATmega328PB-AU

Rpi ibex hyperpixel bill of materials (BOM)

32 components, 18 distinct parts.

QtyPartRefs
1
ATmega328PB-AU
U1
1
SW_Push
U (F7)
1
SW_Push
A (F11)
1
SW_Push
Q (F1)
1
16MHz
Y1
1
SW_Push
Y (F6)
1
Conn_02x05_Odd_Even
J1
1
USART_Connector_1
J2
1
Raspberry_Pi_2_3
J3
1
SW_Push
P (F10)
14
SW_Push
0/) (Esc), 1/! ("), 2/@ ('), 3/# ({), 4/$ ([), 5/% (}), 6/^ (]), 7/& (`) +6
1
1K
1K
1
10K
10K
1
SW_Push
S (F12)
1
SW_Push
T (F5)
2
22pF
C1, C2
1
100nF
C3
1
SW_Push
R (F4)

Rpi ibex hyperpixel design files

The KiCad project lives in the jovan3/rpi-ibex-hyperpixel repository on GitHub; these links point at the commit this page was built from.

Rpi ibex hyperpixel: common questions

What microcontroller does the Rpi ibex hyperpixel use?

The Rpi ibex hyperpixel is built around the ATmega328PB-AU, from the AVR/Arduino family.

How big is the Rpi ibex hyperpixel PCB?

The Rpi ibex hyperpixel measures 99.1 × 113.5 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Rpi ibex hyperpixel?

32 components, from 18 distinct parts. The full bill of materials is listed on this page.

Where can I download the Rpi ibex hyperpixel design files?

From the jovan3/rpi-ibex-hyperpixel repository on GitHub, which has the KiCad layout; the links under Design files point to each one.

Can I use the Rpi ibex hyperpixel design in my own project?

Yes, under the terms of its GPL-3.0 license, which jovan3 chose for the repository.

Can I test firmware for the Rpi ibex hyperpixel without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

Similar boards