BATTERY ISOLATOR V1.1
Just-smart-enough·BATTERY_ISOLATOR_V1.1_PCB
About the BATTERY ISOLATOR V1.1 PCB
BATTERY ISOLATOR V1.1 is an open source STM32 PCB design by Just-smart-enough, published on GitHub under the MIT license. It is a 2-layer board measuring 56 × 50 mm, with 44 components from 28 distinct parts.
Its main chip is the STM32F042F6Px, from the STM32 family. Other key parts include the ACS724xLCTR-30AB, UA78M33QDCYRQ1, UCC27517DBVR and MCP2551-I-SN. By type, the board carries 13 resistors, 8 capacitors, 6 transistors, 5 ICs, 3 test points and 3 diodes.
It belongs with the power & battery designs in this gallery.
From the project
A prototype 12V RV battery isolator
Main components on the BATTERY ISOLATOR V1.1
BATTERY ISOLATOR V1.1 bill of materials (BOM)
44 components, 28 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32F042F6Px | TSSOP-20_4.4x6.5mm_P0.65mm | U1 |
| 1 | ACS724xLCTR-30AB | SOIC-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | UA78M33QDCYRQ1 | SOT-223-3_TabPin2 | U3 |
| 1 | UCC27517DBVR | SOT-23-5 | U4 |
| 1 | MCP2551-I-SN | SOIC-8_3.9x4.9mm_P1.27mm | U5 |
| 2 | AO3400A | SOT-23 | Q1, Q2 |
| 4 | DMTH4008LPS-13 | DMTH4008LPS-13(DI5060-8) | Q3, Q4, Q5, Q6 |
| 1 | HSE | Crystal_SMD_5032-2Pin_5.0x3.2mm | Y2 |
| 1 | PROG | PinHeader_1x04_P1.27mm_Vertical | J3 |
| 1 | CAN 1 | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J23 |
| 1 | CAN TERM | PinHeader_1x02_P2.54mm_Vertical | JP1 |
| 2 | R1K | Potentiometer_Bourns_TC33X_Vertical | RV1, RV2 |
| 1 | MAIN + | SAMZO 8060500M4 | TP1 |
| 1 | AUX + | SAMZO 8060500M4 | TP3 |
| 1 | GND | SAMZO 8060500M4 | TP4 |
| 1 | LED_Dual_Bidirectional | LED_D5.0mm | D1 |
| 2 | C439733 3.0SMCJ20A-13 | D_SMC | D3, D4 |
| 1 | 0.1uf | C_0805_2012Metric | C1 |
| 2 | 2x 22pf | C_0805_2012Metric | C5, C6 |
| 3 | 0.1uf | C_0603_1608Metric | C9, C11, C14 |
Show 8 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 0.33uf | C_0603_1608Metric | C10 |
| 1 | 0.1nF | C_0402_1005Metric | C15 |
| 1 | 4.7k | R_0603_1608Metric | R1 |
| 1 | R120 | R_0603_1608Metric | R2 |
| 6 | R100 | R_0603_1608Metric | R3, R4, R5, R6, R7, R10 |
| 2 | R13K | R_0603_1608Metric | R8, R11 |
| 2 | R2K | R_0603_1608Metric | R9, R12 |
| 1 | R1k | R_0603_1608Metric | R13 |
BATTERY ISOLATOR V1.1 design files
The KiCad project lives in the Just-smart-enough/BATTERY_ISOLATOR_V1.1_PCB repository on GitHub; these links point at the commit this page was built from.
BATTERY ISOLATOR V1.1: common questions
What microcontroller does the BATTERY ISOLATOR V1.1 use?
The BATTERY ISOLATOR V1.1 is built around the STM32F042F6Px, from the STM32 family.
How big is the BATTERY ISOLATOR V1.1 PCB?
The BATTERY ISOLATOR V1.1 measures 56 × 50 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the BATTERY ISOLATOR V1.1?
44 components, from 28 distinct parts. The full bill of materials is listed on this page.
Where can I download the BATTERY ISOLATOR V1.1 design files?
From the Just-smart-enough/BATTERY_ISOLATOR_V1.1_PCB repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the BATTERY ISOLATOR V1.1 design in my own project?
Yes, under the terms of its MIT license, which Just-smart-enough chose for the repository.
Can I test firmware for the BATTERY ISOLATOR V1.1 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k