128 open source boards using the MCP2551-I-SN
Real designs built with the MCP2551-I-SN, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
Jeep canbus
latonita
67.3 × 54 mm48 parts2LMIT30STM32
Noah hardware
GonzaCerv
120 × 100 mm122 parts2LMIT28STM32
Isoblue
oats-center
115 × 78 mm114 parts4LMIT25STM32
Polygonus
FOME-Tech
103 × 82.4 mm299 parts4LNo license21STM32
SMDU
sabanekko3
77.6 × 30.1 mm81 parts4LNo license13STM32
MVCU F407
Vaaarad07
132.9 × 108.4 mm100 parts4LMIT10Megasquirt-MS3-Bootloader
pggood
83.4 × 68.5 mm79 parts4LNo license7STM32
Vesc
LJBoxx
61.5 × 60 mm196 parts4LCERN-OHL-S-2.05STM32
Sensored-3-P-BLDC-Closed-Loop-V1
g-rahul
100 × 100 mm114 parts2LNo license5ESP32
Psa
Mive82
65 × 56 mm106 parts4LNo license5- schematic only · 170 parts
Yatagarasu red
DCoJA
170 partsCC-BY-SA-4.05 STM32
LUT
eddyem
108 × 95 mm93 parts2LGPL-3.04AVR/Arduino
MSWI19
ZeniteSolar
140 × 72.1 mm147 parts2LGPL-3.03AVR/Arduino
Interface board
uvmaero
157.5 × 109.2 mm70 parts2LCC-BY-SA-4.03Raspberry Pi
Chart plotter hat
gpgreen
65 × 56 mm68 parts4LNo license3A123-battery integration
MITEVT
66 × 73.7 mm67 parts4LMIT2AVR/Arduino
Basicsensormodule
ZeniteSolar
121.3 × 52.1 mm50 parts2LGPL-3.02STM32
GCode Buttons MCU
meteyou
50 × 20 mm50 parts4LGPL-3.02ESP32
SLKCAN
czmorris
95.3 × 47 mm42 parts4LMIT2AVR/Arduino
Slave Board
columbia-fsae
412.7 × 77.5 mm148 parts2LNo license1AVR/Arduino
Main
ZeniteSolar
103.5 × 137.2 mm120 parts2LGPL-3.01PIC
EMO OBD tool
darshanram008
35.1 × 62.7 mm102 parts2LCustom license1STM32
STM32F407 Mega converter
mazduino
102 × 53.8 mm94 parts2LNo license1ESP32
LADA
milutintech
137.2 × 61.6 mm90 parts4LNo license1STM32
STM32F4-MotherBoard 5.0.0
mugi111
95.9 × 83.8 mm85 parts2LNo license1AVR/Arduino
ZCS18
ZeniteSolar
102.9 × 45.7 mm69 parts2LLGPL-3.01AVR/Arduino
Vehicle controL module 0.1.0
WATonomous
2.5 × 2.5 mm65 parts2LNo license1Final outline
MITEVT
99.5 × 75 mm57 parts2LMIT1AVR/Arduino
Dash Left
uvmaero
86.4 × 76.2 mm42 parts2LNo license1Servo Tester
Fabien-B
100 × 68 mm36 parts2LNo license1STM32
Watering controller
bendixsonnenberg
96.6 × 132.4 mm30 parts2LMIT1STM32
Fome mc
halbritt
162 × 115 mm462 parts4LNo license0STM32
BDSM G144
matatma23-gento
247.9 × 172.6 mm304 parts4LNo license0ESP32
Open dash daughter
physiii
165.5 × 107.3 mm161 parts2LNo license0STM32
Carte Alim
evolutek
115 × 65 mm132 parts2LNo license0STM32
Stm8-bootloader extended
niksrajendra
40 × 60 mm131 parts2LNo license0
How designs wire the MCP2551-I-SN
Read from the KiCad layouts of 77 open source designs, one per repository: what each pin of the MCP2551-I-SN connects to, and the resistors, capacitors and other passives placed on it.
- The RS pin has a resistor to GND on 61 of 76 designs, most often 10 kΩ (then 4.7 kΩ).
- The VREF pin is left unconnected on 68 of 76 designs (3.3V on 3, a signal on 5).
- The VDD pin has a decoupling capacitor on 51 of 77 designs, most often 100 nF (then 10 µF).
- The CANL pin has a series resistor on 42 of 76 designs, most often 120 Ω (then 100 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VSSpin 2 | Connected to: GND 97% | — |
| VDDpin 3 | Connected to: 5V 92% |
|
| VREFpin 5 | Connected to: Not connected 89% | — |
| CANLpin 6 | Connected to: A connector 86% |
|
| CANHpin 7 | Connected to: A connector 86% |
|
| RSpin 8 | Connected to: Signal 83% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include NMEA2000Adapter-8.1 by peterantypas, RFMote PA by vedderb, Jeep canbus by latonita and Noah hardware by GonzaCerv.
The MCP2551-I-SN in open source designs
The gallery holds 128 open source boards using the MCP2551-I-SN from 81 GitHub repositories; a typical one measures about 82.6 × 65.2 mm and carries around 60 components.
83% are two-layer designs, the rest use four layers or more, and 45% carry an open source license.
The most starred is NMEA2000Adapter-8.1 by peterantypas.
Parts used alongside the MCP2551-I-SN
Microcontrollers on boards using the MCP2551-I-SN
What boards using the MCP2551-I-SN are built for
MCP2551-I-SN: common questions
Where can I find a MCP2551-I-SN reference design?
Each of the 128 boards on this page is a real design using the MCP2551-I-SN. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the MCP2551-I-SN RS pin?
The RS pin has a resistor to GND on 61 of 76 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 77 open source designs using the MCP2551-I-SN.
How is the MCP2551-I-SN VREF pin connected?
The VREF pin is left unconnected on 68 of 76 designs (3.3V on 3, a signal on 5). Counted from the KiCad layouts of 77 open source designs using the MCP2551-I-SN.
What decoupling capacitors do designs use on the MCP2551-I-SN VDD pin?
The VDD pin has a decoupling capacitor on 51 of 77 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 77 open source designs using the MCP2551-I-SN.
What parts are used alongside the MCP2551-I-SN?
The MCP2515-xSO, LM7805, AMS1117-3.3, ATmega328P-PU and LPC11C14 appear in the most repositories here.
Which microcontrollers do boards using the MCP2551-I-SN use?
Most are built on AVR/Arduino (45), STM32 (38), ESP32 (13) and Raspberry Pi (5).
How big is a typical board using the MCP2551-I-SN?
The median is 82.6 × 65.2 mm, and 83% are two-layer designs.
What is the most popular open source board using the MCP2551-I-SN?
By GitHub stars, NMEA2000Adapter-8.1 by peterantypas, with 446 stars.
Can I simulate one of these boards using the MCP2551-I-SN before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.